Sony HD 3CCD User Manual
Ov
er
v
er
v
ie
w
Location and Function of Parts
19
O EXT SYNC IN connector
Accepts external video sync signals.
P Card slot
Insert an optional interface board, HFBK-HD1,
HFBK-SD1, HFBK-XG1, HFBK-TS1 or BRBK-
H700.
The slot cover is attached to the camera at the
factory.
HFBK-SD1, HFBK-XG1, HFBK-TS1 or BRBK-
H700.
The slot cover is attached to the camera at the
factory.
Q
RGB/COMPONENT connector
Supplies the images as analog component (YPbPr
or RGB) signal.
or RGB) signal.
R DATA MIX switch
Set the switch to ON to overlap the menu with the
video signal output from the installed interface
board. Set it to OFF not to overlap the menu.
video signal output from the installed interface
board. Set it to OFF not to overlap the menu.
S Cable cover
The cable cover is attached to the camera at the
factory. To remove the cable cover, see page 50.
factory. To remove the cable cover, see page 50.
Note
Do not carry the camera by holding the cable cover.
Otherwise, the cable cover may come off and the
camera may fall.
Otherwise, the cable cover may come off and the
camera may fall.
Bottom
T Ceiling bracket mounting screw holes
When you install the camera to the ceiling, secure
the supplied ceiling bracket to these holes using the
supplied four screws. The four feet are attached to
the holes at the factory.
the supplied ceiling bracket to these holes using the
supplied four screws. The four feet are attached to
the holes at the factory.
For installation, see “Installing the Camera on the
Ceiling” on page 52.
Ceiling” on page 52.
U Tripod screw holes (1/4-20UNC)
When you install the camera to a tripod, secure the
tripod to these holes.
tripod to these holes.
V BOTTOM switches
Used for the output signal format selection, RS-
232C/RS-422 selection, baud rate selection, remote
control signal output on/off and camera address
setting.
232C/RS-422 selection, baud rate selection, remote
control signal output on/off and camera address
setting.
For details, see “Setting of the BOTTOM switches”
on page 19.
on page 19.
Setting of the BOTTOM switches
1
Switch 1 (59.94i/50i signal format selector)
Set to ON for output of 50i signal format, or OFF
for output of 59.94i signal format.
Set to ON for output of 50i signal format, or OFF
for output of 59.94i signal format.
2
Switch 2 (RS-232C/RS-422 selector)
Set to ON for RS-422, or OFF for RS-232C.
Set to ON for RS-422, or OFF for RS-232C.
3
Switch 3 (Communication baud rate selector)
Set to ON for 38400bps, or OFF for 9600bps.
Set to ON for 38400bps, or OFF for 9600bps.
4
Switch 4 (Infrared signal output switch)
Set to ON to enable an infrared signal output, or
OFF to disable the output.
Set to ON to enable an infrared signal output, or
OFF to disable the output.
5
Camera address selectors
Set the address of the camera.
Normally set to “0”. With this setting, addresses
are assigned to the cameras automatically in the
connected order by pressing the POWER button
while holding down the RESET button on the RM-
BR300 Remote Control Unit.
You can assign the camera address “1” to “7”
manually by setting these selectors as follows:
Set the address of the camera.
Normally set to “0”. With this setting, addresses
are assigned to the cameras automatically in the
connected order by pressing the POWER button
while holding down the RESET button on the RM-
BR300 Remote Control Unit.
You can assign the camera address “1” to “7”
manually by setting these selectors as follows:
Switch 4 is not used.
Note
Set the switches before you turn on the power of the
camera.
camera.
wa
w;
ws
Camera
address
address
0
1
2
3
4
5
6
7
Switch 1
OFF ON
OFF ON
OFF ON
OFF ON
Switch 2
OFF OFF ON
ON
OFF OFF ON
ON
Switch 3
OFF OFF OFF OFF ON
ON
ON
ON
O
N
N
1
2
3
4
2
3
4
O
N
N
1
2
3
4
2
3
4
2
1
4
5
5
3