Sony SVO-1330 User Manual
14
(US)
Recording the date and time
You can record the recording date and time on the tape
together with the picture.
together with the picture.
Set the ON SCREEN ON/OFF switch to ON. The
current date and time are displayed on the screen. If
you start recording in this condition, the displayed date
and time are recorded on the tape together with the
picture.
To turn off the date and time, set the ON SCREEN
ON/OFF switch to OFF.
current date and time are displayed on the screen. If
you start recording in this condition, the displayed date
and time are recorded on the tape together with the
picture.
To turn off the date and time, set the ON SCREEN
ON/OFF switch to OFF.
Setting the timing of the tape-
end alarm
end alarm
You can select the timing at which the TAPE END
buzzer beeps to indicate the tape reaches its end or the
nominal tape length (before its end).
buzzer beeps to indicate the tape reaches its end or the
nominal tape length (before its end).
1
Press MENU and select 3.SET UP/USED TIME
using SHIFT
using SHIFT
v, then press SHIFT b.
The SET UP menu appears on the screen.
2
Press SHIFT
v to flash the setting of “END
ALARM.”
3
Set “END ALARM” to END or 02:00 for example
(nominal tape length), using DATA +/–.
(nominal tape length), using DATA +/–.
[ SET UP ]
[ USED TIME ]
HEAD 00005H
HEAD 00005H
END ALARM
TAPE END
TAPE END
CLOCK ADJ
BUZZER
THREAD CHECK
BUZZER
THREAD CHECK
TAPE
APC
T-120
END
REW
ON
0 1 : 0 0
ON
ON
END
REW
ON
0 1 : 0 0
ON
ON
ON SCREEN ON/OFF
Recording
6
r
P
p
0
(
)
END: An alarm signal is output when the tape
reaches its end.
02:00, etc.: An alarm signal is output when the
tape counter shows the set time (that is, the
nominal tape length in hours and minutes).
The time that appears depends on the setting of
“TAPE” and the recording tape speed (SP or
EP). Set the tape length correctly on “TAPE”
(T-120 or T-160).
When “TAPE” is set to T-120, 02:00 appears in
SP mode or 06:00 in EP mode;
When “TAPE” is set to T-160, 02:40 appears in
SP mode or 08:00 in EP mode.
nominal tape length in hours and minutes).
The time that appears depends on the setting of
“TAPE” and the recording tape speed (SP or
EP). Set the tape length correctly on “TAPE”
(T-120 or T-160).
When “TAPE” is set to T-120, 02:00 appears in
SP mode or 06:00 in EP mode;
When “TAPE” is set to T-160, 02:40 appears in
SP mode or 08:00 in EP mode.
4
Press SHIFT
v to flash the setting of “TAPE” and
set it to T-120 or T-160 using DATA +/–.
(You may skip this step if you set “END ALARM”
to END in step 3.)
(You may skip this step if you set “END ALARM”
to END in step 3.)
[ SET UP ]
[ USED TIME ]
HEAD 00005H
HEAD 00005H
END ALARM
TAPE END
TAPE END
CLOCK ADJ
BUZZER
THREAD CHECK
BUZZER
THREAD CHECK
TAPE
APC
T-160
0 2 : 4 0
REW
ON
0 1 : 0 0
ON
ON
0 2 : 4 0
REW
ON
0 1 : 0 0
ON
ON
5
Press MENU twice to return to the normal display.
Setting the mode at the end of
the tape
the tape
You can rewind or eject the tape when it comes to the
end during recording.
end during recording.
1
Press MENU and select 3.SET UP/USED TIME
using SHIFT
using SHIFT
v, then press SHIFT b.
The SET UP menu appears on the screen.
2
Press SHIFT
v to flash the setting of “TAPE
END.”