Sony super had ccd ssc-cd49p User Manual
English
Installation
Before Installation
D
After deciding the direction in which the camera will shoot, make the
required hole (ø 40 to 60 mm (ø 1
required hole (ø 40 to 60 mm (ø 1
5
/
8
to 2
3
/
8
in.)) for the connecting cables
using the supplied template. Then decide the two mounting hole positions
to install the camera unit.
to install the camera unit.
Mounting screws
The supplied stand is provided with two ø 5 mm (7/32 in.) mounting holes.
Install the stand to a ceiling or wall with screws through these holes.
The required mounting screws differ depending on the installation location
and its material.
Steel wall or ceiling: Use M4 bolts and nuts.
Wood wall or ceiling: Use the M4 tapping screws. The panel thickness
must be 15 mm (5/8 in.) or more.
Concrete wall: Use appropriate anchors, bolts and plugs for concrete
walls.
Junction box: Use screws to match the holes on the junction box.
Install the stand to a ceiling or wall with screws through these holes.
The required mounting screws differ depending on the installation location
and its material.
Steel wall or ceiling: Use M4 bolts and nuts.
Wood wall or ceiling: Use the M4 tapping screws. The panel thickness
must be 15 mm (5/8 in.) or more.
Concrete wall: Use appropriate anchors, bolts and plugs for concrete
walls.
Junction box: Use screws to match the holes on the junction box.
WARNING
The required mounting screws differ depending on the installation location
and its material. If you do not secure the camera with the appropriate
mounting screws, the camera may fall off.
and its material. If you do not secure the camera with the appropriate
mounting screws, the camera may fall off.
Installing the Camera
1
Remove the dome casing. (E)
1
Pull out the screw cover and loosen the screw with a Phillips
screwdriver.
screwdriver.
2
Turn the dome casing to the carved mark position on the camera
unit, and remove the dome casing from the camera unit. When the
screw is caught on the screw hole, pull up the screw.
unit, and remove the dome casing from the camera unit. When the
screw is caught on the screw hole, pull up the screw.
2
Remove the slit cover.
Remove it expanding the slit cover. (F)
3
When installing on a ceiling or wall, fix the supplied wire rope to the
camera and the ceiling or wall. (G)
camera and the ceiling or wall. (G)
1
Fix the wire rope with the supplied shoulder screw to the hole for
the wire rope on the bottom of the camera.
the wire rope on the bottom of the camera.
2
Fix the wire rope to the ceiling or wall.
4
Attach the camera unit to the ceiling or wall with the mounting screws.
WARNING
• If you want to install the camera at a height such as on a ceiling,
entrust the installation to an experienced contractor or installer.
• If you install the camera in the height, ensure that the installation
location and it material are strong enough to withstand a weight of
10 kg (22 lb 1 oz) or more, and then install the camera securely. If
they are not strong enough, the camera may fall and cause serious
injury.
10 kg (22 lb 1 oz) or more, and then install the camera securely. If
they are not strong enough, the camera may fall and cause serious
injury.
• To prevent the camera from falling, be sure to attach the supplied
wire rope.
• If you install the camera at a height, check periodically, at least once
a year, to ensure that the connection has not loosened. If conditions
warrant, perform this periodic check more frequently.
warrant, perform this periodic check more frequently.
Note
If you cannot use screws on a ceiling or wall, or if you want to make
the camera less conspicuous, use the YT-ICB45 in-ceiling bracket
(optional) with which you can mount the camera on the ceiling.
the camera less conspicuous, use the YT-ICB45 in-ceiling bracket
(optional) with which you can mount the camera on the ceiling.
D
E
F
H
K
Hole for the
connecting cable/
connecting cable/
Camera installation
hole/
hole/
G
Side/
Bottom/
ø5 (
7
/
32
)
Unit: mm (inches)/
Ceiling/
83.5 (3
9
/
32
)
ø126 (5)
97.5 (3
7
/
8
)
1
2
Wire rope/
2
1, 3
4, 7
5
6
6
I
1
2
Adjusting the Camera Direction and CoverageH
1
Loosen the camera head fixing screw.
2
Adjust the camera to turn the lens in the desired direction.
3
Tighten the camera head fixing screw to fix the camera.
4
Loosen the lens ring fixing screw.
5
Turn the zoom ring to adjust the angle of view.
6
Turn the focus ring to adjust the focus.
7
Tighten the lens ring fixing screw to fix the zoom and the focus.
8
Repeat steps 1 to 7 until the coverage and the focus are determined.
Notes
• When you adjust the camera head angle without loosening camera
head fixing screw, an internal metallic part may be damaged.
• If the camera head is too heavy to be adjusted, loosen the camera
head fixing screw until it moves freely.
• When the lens is not put in the slit of the camera head holder, the
moving range of the camera head is limited.
• Do not turn the lens more than 360 degrees. As this may damage
the wiring inside.
• There are three screw holes for fixing the lens ring at 120 degree
intervals. If the lens ring fixing screw poses a problem for adjusting
the camera direction and coverage due to the direction of the
camera head, detach the screw and reattach it to another screw
hole, then adjust the camera direction and coverage again.
the camera direction and coverage due to the direction of the
camera head, detach the screw and reattach it to another screw
hole, then adjust the camera direction and coverage again.
• When adjusting the angle, be sure that the TOP mark on the camera
head section faces the ceiling. If the camera is installed with the
TOP mark facing the floor, the image appears upside down.
TOP mark facing the floor, the image appears upside down.
Attaching the Dome Casing
1
Attach the slit cover. (I)
Notes
• The proper position of the slit cover is slightly apart from the camera
mount. Do not push in by force.
• If you cannot attach the slit cover because the barrier of the lens
ring fixing screw prevents it, attach the lens ring fixing screw to
another screw hole. There are three screw holes for the lens ring
fixing screw on the concentric circle.
another screw hole. There are three screw holes for the lens ring
fixing screw on the concentric circle.
2
Fix the dome casing and the camera unit. (J)
1
Align the carved mark of the dome casing with the one on the
camera unit, and turn the dome casing in the direction of the arrow.
camera unit, and turn the dome casing in the direction of the arrow.
2
Secure the dome casing with the supplied dome casing screw.
Then, return the screw cover to the screw hole on the dome casing.
Then, return the screw cover to the screw hole on the dome casing.
Specifications
Image device
1/3 type interline transfer (Super HAD CCD
for SSC-CD45/CD45P, DynaView for
SSC-CD49/CD49P)
SSC-CD49/CD49P)
Effective picture elements
SSC-CD45/CD49:
768 (horizontal) × 494 (vertical)
SSC-CD45P/CD49P:
752 (horizontal) × 582 (vertical)
Focal length
2.8 to 10 mm
Maximum relative aperture F1.3
View angle
View angle
Horizontal: 100.8° (wide) – 27.7° (tele)
Vertical: 73.9° (wide) – 20.8° (tele)
Vertical: 73.9° (wide) – 20.8° (tele)
Minimum object distance
0.3 m
Signal system
SSC-CD45/CD49: NTSC color system
SSC-CD45P/CD49P: PAL color system
SSC-CD45P/CD49P: PAL color system
Synchronization system
Internal (DC 12 V/AC 24 V)/
Line lock (AC 24 V only) switchable
Line lock (AC 24 V only) switchable
Horizontal resolution
SSC-CD45/CD45P: 540 TV lines
SSC-CD49/CD49P: 480 TV lines
SSC-CD49/CD49P: 480 TV lines
Minimum illumination
SSC-CD45/CD45P:0.9 lx (AGC ON, F1.3,
50IRE)
SSC-CD49/CD49P: 0.7 lx (AGC ON, F1.3,
50IRE)
Video output
1.0 Vp-p, 75 ohms, negative sync, BNC
cable
Video S/N ratio
More than 50 dB (AGC OFF)
White balance
ATW/ATW Pro switchable
AGC
ON / OFF switchable
BLC
SSC-CD45/CD45P: ON / OFF switchable
(BLC ON)
SSC-CD49/CD49P: ON / OFF switchable
(DynaView ON)
Monitor output
Phono jack
Power supply
SSC-CD45/CD49: AC 24 V ±10 % / 60Hz,
DC 12 V ±10 %
(Automatically switched)
(Automatically switched)
SSC-CD45P/CD49P: AC 24 V ±10 % / 50Hz,
DC 12 V ±10 %
(Automatically switched)
(Automatically switched)
Power consumption
SSC-CD45/CD45P: 4.0 W
SSC-CD49/CD49P: 4.2 W
SSC-CD49/CD49P: 4.2 W
Operating temperature
–20 °C to +50 °C (–4 °F to +122 °F)
Storage temperature
–40 °C to +60 °C (–40 °F to +140 °F)
Operating humidity
20% to 80%
Storage humidity
20% to 95%
Dimensions (diameter/height) (K)
126 × 97.5 mm (5 × 3
7
/
8
inches)
Mass
Approx. 440 g (16 oz)
Supplied accessories
M4 Shoulder screw (1)
Wire rope (1)
Template (1)
Operating Instructions (1)
Wire rope (1)
Template (1)
Operating Instructions (1)
Optional accessory
In-ceiling bracket
YT-ICB45
Design and specifications are subject to change without notice.
Always verify that the unit is operating properly before use. SONY WILL
NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT
LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT
OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO
FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD
OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER
REASON WHATSOEVER.
NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT
LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT
OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO
FAILURE OF THIS UNIT, EITHER DURING THE WARRANTY PERIOD
OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER
REASON WHATSOEVER.
Regular parts replacement
Some of the parts that make up this product (electrolytic condenser, for
example) need replacing regularly depending on their life expectancies.
The lives of parts differ according to the environment or condition in
which this product is used and the length of time it is used, so we
recommend regular checks.
Consult the dealer from whom you bought it for details.
example) need replacing regularly depending on their life expectancies.
The lives of parts differ according to the environment or condition in
which this product is used and the length of time it is used, so we
recommend regular checks.
Consult the dealer from whom you bought it for details.
Slit cover/
J
83.5 (3
9
/
32
)
Lens ring fixing
screw holes/
screw holes/
Dome casing/