Panasonic ag-vp300 User Manual
54
Error Messages
Before requesting service, check the following points once again.
On Screen Display
ª VCR
ª DVD
Self-diagnostic Indications
This unit has a self-diagnosis and display function. If this unit detects trouble during installation or during use, the following indications
automatically appear in the unit’s display. Indications are in the form of a single English letter plus two numbers, such as [H01].
automatically appear in the unit’s display. Indications are in the form of a single English letter plus two numbers, such as [H01].
ª VCR
ª DVD
PLEASE PUT IN A VIDEO
CASSETTE.
CASSETTE.
≥[REC¥] (¥REC/OTR) or [TIMER
] (
TIMER REC) has been pressed without a video
cassette inserted.
Insert a video cassette with an intact erasure prevention tab.
Insert a video cassette with an intact erasure prevention tab.
PLEASE STOP THE
TAPE.
TAPE.
≥CHANNEL SET has been selected during playback. Stop the tape.
PLEASE SET THE
CLOCK.
CLOCK.
≥[TIMER
] (
TIMER REC) or [PROG/CHECK] has been pressed when the clock is not set.
Set the clock.
PLEASE USE A
CASSETTE WITH TAB.
CASSETTE WITH TAB.
≥[REC¥] (¥REC/OTR) or [TIMER
] (
TIMER REC) has been pressed without a video
cassette with an intact erasure prevention tab.
Use a video cassette with an intact erasure prevention tab.
Use a video cassette with an intact erasure prevention tab.
NO TIMER RECORDING
HAS BEEN SET.
HAS BEEN SET.
≥[TIMER
] (
TIMER REC) has been pressed with no timer programs.
Set timer recording.
Cannot display group xx,
picture xx
picture xx
≥You are trying to display incompatible pictures.
—
The progressive out is set
to “Disable”
to “Disable”
≥Go to “Video” in the SET UP menus, and select “Enable” in “Progressive Out (Component)”.
H
∑∑, F∑∑
(
∑∑ stands for a number.)
≥An error has occurred. The number following “H” or “F” depends on the status of the unit.
Reset procedure:
Press [POWER
Press [POWER
Í/I] to switch the unit to the standby mode and then back to ON. Alternatively,
press [POWER
Í/I] to switch the unit to the standby mode, disconnect the AC power supply
cord, and then reconnect it.
≥If the service numbers fail to clear, note the service number and contact a qualified service
person.
—
—
U11
≥Disc is dirty. Wipe it clean.
H
∑∑, F∑∑
(
∑∑ stands for a number.)
≥An error has occurred. The number following “H” or “F” depends on the status of the unit.
Reset procedure:
Press [POWER
Press [POWER
Í/I] to switch the unit to the standby mode and then back to ON. Alternatively,
press [POWER
Í/I] to switch the unit to the standby mode, disconnect the AC power supply
cord, and then reconnect it.
≥If the service numbers fail to clear, note the service number and contact a qualified service
person.
—
No DISC
≥You haven’t inserted a disc; insert one.
≥You haven’t inserted the disc correctly; insert it correctly.
≥You haven’t inserted the disc correctly; insert it correctly.
—
No PLAY
≥You inserted a disc the unit cannot play.
≥You inserted a blank DVD-RAM.
≥A disc whose playback is restricted in the SET UP menus, “Disc”
≥You inserted a blank DVD-RAM.
≥A disc whose playback is restricted in the SET UP menus, “Disc”
l”Ratings”, is inserted.
Change the “Ratings” setting.
—
ERROR
≥Incorrect operation performed. Read the instructions and try again.
—
VP300P.book Page 54 Thursday, March 20, 2003 10:21 AM