Panasonic AJ-HD1400P User Manual
39
Setup menus
(continued)
BASIC (continued)
*1 Displayed menus may vary depending on the settings in
menu No. 25 SYSTEM FREQ. For details, refer to
“Menus which are displayed” (page 32).
“Menus which are displayed” (page 32).
“_____” indicates the factory setting.
Formats for playback
Depending on how the menu item No.020 SYS FORMAT,
No.022 PB FORMAT and No.023 FORMAL SEL settings are
combined, the formats of the tapes played back by the unit
differ as shown in the table below.
No.022 PB FORMAT and No.023 FORMAL SEL settings are
combined, the formats of the tapes played back by the unit
differ as shown in the table below.
<Notes>
z When the tape is ejected, the format follows the one
selected by menu item No.020 SYS FORMAT setting.
z DVCPRO P playback is not possible.
No./Item
Description of setting
030*
1
HD
FREQUENCY
FREQUENCY
For setting the field frequency.
0000
0000
59/23 :
The field frequency is set to 59.94/23.98 Hz.
0001
60/24 :
The field frequency is set to 60/24 Hz.
<Note>
The field frequency which is set here takes effect only
when there is no input which supports the OUT REF
setting.
If there is an input which supports the setting, the
field frequency is consistent with the field frequency
of input.
The field frequency which is set here takes effect only
when there is no input which supports the OUT REF
setting.
If there is an input which supports the setting, the
field frequency is consistent with the field frequency
of input.
031*
1
OUT REF
For selecting the video output reference.
0000
0000
AUTO :
The REF signal (HD/SD) which is input to the REF
connector is automatically identified and serves as
the reference.
If no signal is supplied to the REF connector, the
HD serial input signal serves as the reference.
If neither the REF input signal nor HD serial input
signal is supplied, the unit’s internal reference is
used.
connector is automatically identified and serves as
the reference.
If no signal is supplied to the REF connector, the
HD serial input signal serves as the reference.
If neither the REF input signal nor HD serial input
signal is supplied, the unit’s internal reference is
used.
0001
INPUT :
The input signal serves as the reference.
If this signal is not available, the unit’s internal
reference is used.
If this signal is not available, the unit’s internal
reference is used.
0002
HD REF :
The HD REF input signal serves as the reference.
If this signal is not available, the unit’s internal
reference is used.
If this signal is not available, the unit’s internal
reference is used.
0003
SD REF :
The SD REF input signal serves as the reference.
If this signal is not available, the unit’s internal
reference is used.
If this signal is not available, the unit’s internal
reference is used.
0004
E-AUTO :
When the editing mode is selected, the state is the
same as when set to “INPUT.”
When any mode other than the editing mode is
selected, the state is the same as when set to
“AUTO.”
For details, refer to “Reference signals” (page 16).
same as when set to “INPUT.”
When any mode other than the editing mode is
selected, the state is the same as when set to
“AUTO.”
For details, refer to “Reference signals” (page 16).
032*
1
REC REF
Select the reference to synchronize the image frames
for recording.
0000
for recording.
0000
NORMAL :
The video signal which is input is automatically
identified and serves as the reference.
identified and serves as the reference.
0001
SLTC :
The time code which is input to the HD SDI IN
connector isidentified and serves as the reference.
connector isidentified and serves as the reference.
<Note>
When the SLTC is selected, the following settings are
necessary to validate the settings for this item.
z Menu No. 25 SYSTEM FREQ: 59/60
z Menu No. 020 SYS FORMAT: 720p
z INPUT SELECT button on the front panel: HDSDI
When the SLTC is selected, the following settings are
necessary to validate the settings for this item.
z Menu No. 25 SYSTEM FREQ: 59/60
z Menu No. 020 SYS FORMAT: 720p
z INPUT SELECT button on the front panel: HDSDI
022.
PB FORMAT
PB FORMAT
020.
SYS FORMAT
SYS FORMAT
023.
FORMAT SEL
FORMAT SEL
Playback format
MANUAL
1080i
HD_LP
DVCPRO HD-LP (1080i)
HD_SP
DVCPRO HD (1080i)
50M
DVCPRO50 (422)
25M
DVCPRO (411)
DV
DV
DVCAM
DVCAM
720P
HD_LP
DVCPRO HD-LP (720p)
HD_SP
DVCPRO HD (720p)
50M
DVCPRO50 (422)
25M
DVCPRO (411)
DV
DV
DVCAM
DVCAM
AUTO
If AUTO is selected as the
menu item No.022 PB
FORMAT setting, the
format applying when the
format is not yet detected
(when the tape inserted)
follows the menu item
No.023 FORMAL SEL
setting.
However, if “DV” or
“DVCAM” is selected,
operation proceeds as if
“HD_LP” is selected.
menu item No.022 PB
FORMAT setting, the
format applying when the
format is not yet detected
(when the tape inserted)
follows the menu item
No.023 FORMAL SEL
setting.
However, if “DV” or
“DVCAM” is selected,
operation proceeds as if
“HD_LP” is selected.
DVCPRO HD-LP
(1080i/720p),
DVCPRO HD (1080i/
720p), DVCPRO50
(422), DVCPRO (411),
DVCPROP (420p), DC
or DVCAM format is
detected automatically.
(1080i/720p),
DVCPRO HD (1080i/
720p), DVCPRO50
(422), DVCPRO (411),
DVCPROP (420p), DC
or DVCAM format is
detected automatically.