Panasonic AJ-HD1400P User Manual

37

*1 Displayed menus may vary depending on the settings in

menu No. 25 SYSTEM FREQ. For details, refer to
“Menus which are displayed” (page 32).

“_____” indicates the factory setting.

For selecting the system frequency.
For details, refer to “Procedure for shifting the system 
frequency" (page 31).
0000

The 59.94 Hz or 60 Hz system frequency is 
selected.

The 50 Hz or 25 PsF system frequency is selected.
At this setting, the 1080/25 PsF format signals can 
be recorded and played back in the same way as 
with the 1080/50i format.

The 23.98 Hz or 24 Hz system frequency is 
selected.

The 25 Hz system frequency is selected. However, 
black signals are output from the SD SDI output 
and analog composite connectors.

The 25 Hz system frequency is selected. However, 
black signals are output from the HD SDI output 
and analog component connectors.

The 50 Hz system frequency is selected. However, 
black signals are output from the SD SDI output 
and analog composite connectors.

The 50 Hz system frequency is selected. However, 
black signals are output from the HD SDI output 
and analog component connectors.

For selecting the output whose HD output phase is to 
be advanced by 90H in relation to the SD output.
0000

Both the HD and SD signals are output in phase 
with the HD and SD REF output signals.

The HD signals are output at a phase advanced by 
90H from the SD output signals.
When the SD REF signal is input, the REF input 
and SD output are in-phase, and when the HD REF 
signal is input, the REF input and HD output are 
inphase.

<Notes>
z The audio signals and TC signal are output in 

phase with the HD output.

z With the 720p format, there is a phase difference of 

120H between them.

For setting the operable buttons on the front panel 
when the REMOTE/LOCAL switch is set to 
“REMOTE.”
0000

None of the buttons can be operated.

Only the STOP and EJECT buttons can be 
operated.

All of the buttons with the exception of COUNTER 
and RESET can be operated.

All of the buttons can be operated.

For setting how the time is to be displayed on the CTL 
counter display.
0000

12-hour display

24-hour display

For setting the remaining time on the tape for the 
respective connectors and the superimposed 
indications of the total length of the tape.
0000

No displays are superimposed.

The remaining tape time is displayed on the 
second line.

The remaining tape time is displayed on the first 
line.

The remaining tape time is displayed on the first 
line and the total tape duration on the second line.

<Note>
The information will not be displayed when “2L” or “R/
TTL” is set and TIME is selected as the menu item 
No.006 DISPLAY SEL setting.

For setting the superimposing of the displays onto 
various connectors.
0000

The displays are superimposed onto none of the 
output connectors.

The displays are superimposed onto the analog 
composite output.

The displays are superimposed onto the HD 
analog component output.

The displays are superimposed onto SD SDI OUT.

The displays are superimposed onto HD SDI OUT.

The displays are superimposed onto the analog 
composite output and SD SDI OUT.

The displays are superimposed onto the HD 
analog component output and HD SDI OUT.

<Notes>
z The information will not be displayed when the 

SUPER switch is OFF.

z 1394 output is according to Menu No. 899 DIF 

SUPER.

z If the 23.98/24 Hz, 25 Hz (HD), or 50 Hz (HD)

mode is selected in menu No. 25 SYSTEM FREQ,
no super is displayed on the analog composite
output and the SD SDI output.
If the 25 Hz (SD) or 50 Hz (SD) mode is selected, 
no super is displayed on the analog component 
output and the HD SDI output.