Panasonic nv-hv22gn User Manual
4
Connections
This section shows you how to connect the VCR to an aerial,
TV, etc.
TV, etc.
Basic Connections
The following connections are required to record and play
back the video cassette through the TV.
back the video cassette through the TV.
Connection to a TV using the Audio/Video Input Socket:
Set the RF output channel of the VCR to [
Set the RF output channel of the VCR to [
ss] (RF OFF)
when the VCR is connected to the TV via the Audio/Video
cable. (See to the right.)
cable. (See to the right.)
Tuning the TV to Your VCR
The VCR supplies a signal to the TV via the RF coaxial cable
on channel AU28-69 or NZ21-69.
If you have connected the VCR to the TV through the Audio/
Video input sockets, then you do not need to follow the
procedure below. To view the pictures from the VCR, set to
the AV mode on the TV with [AV]
on channel AU28-69 or NZ21-69.
If you have connected the VCR to the TV through the Audio/
Video input sockets, then you do not need to follow the
procedure below. To view the pictures from the VCR, set to
the AV mode on the TV with [AV]
(2).
Preparation
• Turn on the TV and the VCR.
Operations
1 Hold down [MENU]
• Turn on the TV and the VCR.
Operations
1 Hold down [MENU]
(9) for 5 seconds or more.
2 Set the TV to an unused position which you wish to
use for your video playback.
• Tune the TV until the display shown below appears on
the screen. (Please refer to the TV manufacturers
operating instructions regarding tuning.)
operating instructions regarding tuning.)
3 Press [MENU]
(9).
To Change the RF output Channel
You can change the RF output channel, for example, when
interference occurs on the picture after tuning.
interference occurs on the picture after tuning.
Operations
1 Hold down [MENU]
1 Hold down [MENU]
(9) for 5 seconds or more.
• The VCR display changes as shown below and the VCR
picture on the TV displays this pattern.
2 Enter the desired channel number (AU28-69, NZ21-69)
by [Numeric]
(3) or [CH] (20).
• Set the RF output channel of the VCR to [
ss] (RF OFF)
when the VCR is connected to the TV via the Audio/Video
cable.
cable.
• Press [CH]
(20) to display [
ss].
• It is also possible to select by pressing [Numeric]
(3).
Example:
3 Press [MENU]
(9) to finish the setting mode.
4 Retune your TV to the new RF channel for the VCR.
Note:
• Even if the RF output channel has been changed, it is not
• Even if the RF output channel has been changed, it is not
necessary to perform Auto Tuning.
AUDIO
VIDEO
AC IN
∼
OUT
IN(AV1)
IN
OUT
RF
(6)
(3)
(5)
(4)
(1)
(2)
¢
(1) Aerial (Not supplied)
(2) TV Set (Not supplied)
(3) Aerial Connector
(4) RF IN socket
(2) TV Set (Not supplied)
(3) Aerial Connector
(4) RF IN socket
(42)
(5) RF OUT socket
(45)
(6) AC Input socket
(39)
¢ To mains supply
AUDIO
VIDEO
AC IN
∼
OUT
IN(AV1)
IN
OUT
RF
(10)
(3)
(4)
(6)
(5)
(9)
(8)
(7)
(1)
(2)
¢
(1) Aerial (Not supplied)
(2) TV Set (Not supplied)
(3) Aerial Connector
(4) VIDEO IN
(5) AUDIO IN
(6) Audio Cable/Video Cable
(2) TV Set (Not supplied)
(3) Aerial Connector
(4) VIDEO IN
(5) AUDIO IN
(6) Audio Cable/Video Cable
(Not supplied)
(7) RF IN socket
(42)
(8) RF OUT socket
(45)
(9) VIDEO OUT
(41)/
AUDIO OUT
(10)AC Input socket
(39)
¢ To mains supply
Panasonic VCR
END: MENU
Panasonic VCR
END: MENU
Example for Australia
Example for New Zealand
ss
…
…
…
(Initial position)
For New Zealand
For Australia
(RF OFF)
E-21
E-69
A-28
A-37
A-69
2
8
28:
LSQT0879.book 4 ページ ２００５年２月２３日 水曜日 午後８時４９分