Manualsbrain.com
  1. Manuals
  2. Brands
  3. Panasonic
  4. wv-cm146
  5. User Manual

Panasonic wv-cm146 User Manual

Download
Page of 22
-9-
1-1. Move the cursor to 
"
CAMERA ID,
"
and select the desired camera
using the Left (
A) or Right switch (B).
To display camera identification, press the SET UP switch.
1-2. After completing item 1, move the cursor to the second line using
the Down switch (
C).
Set camera identification as in 1-3 below and press the SET UP
switch.
To register the camera identification, move the cursor back to
"
CAMERA ID.
"
1-3. Selectable characters are shown below.
   ** SET UP MENU **
CAMERA ID       1.34..7.
              1 CAMERA
AUDIO SELECT    1
TIMING SELECT   INT
SEQ TIME ADJ    1SEC
PAGE SEQ        2SEC
ALARM REC MODE  FRAME
ALARM TIME ADJ  10SEC BZ
AUTO RESET      OFF
BRIGHT COMP     12..5..8
  END   SET UP ENABLE
2-1. Move the cursor to 
"
AUDIO SELECT.
"
Select 
"
SEQ
"
(sequential) or 
"
1, 2, 3, 4
"
(fixed) using the Left (
A) or
Right switch (
B).
2-2. In 
"
SEQ,
"
the audio signal is also switched according to channel
switching.
2-3. In 
"
1, 2, 3, 4
"
(fixed,) the audio signal is fixed to the selected chan-
nel.
Note:
During the fixed channel is selected, the audio of the select-
ed channel changes to the alarmed channel if the alarm signal
is received.
The following table shows the audio sequential time when SEQ is
selected for AUDIO SELECT.
   ** SET UP MENU **
CAMERA ID       1.34..7.
              1 CAMERA
AUDIO SELECT    1
TIMING SELECT   INT
SEQ TIME ADJ    1SEC
PAGE SEQ        2SEC
ALARM REC MODE  FRAME
ALARM TIME ADJ  10SEC BZ
AUTO RESET      OFF
BRIGHT COMP     12..5..8
  END   SET UP ENABLE
   ** SET UP MENU **
CAMERA ID       1.34..7.
              1 CAMERA
AUDIO SELECT    1
TIMING SELECT   INT
SEQ TIME ADJ    1SEC
PAGE SEQ        2SEC
ALARM REC MODE  FRAME
ALARM TIME ADJ  10SEC BZ
AUTO RESET      OFF
BRIGHT COMP     12..5..8
  END   SET UP ENABLE
   ** SET UP MENU **
CAMERA ID       1.34..7.
              1 CAMERA
AUDIO SELECT    1
TIMING SELECT   INT
SEQ TIME ADJ    1SEC
PAGE SEQ        2SEC
ALARM REC MODE  FRAME
ALARM TIME ADJ  10SEC BZ
AUTO RESET      OFF
BRIGHT COMP     12..5..8
  END   SET UP ENABLE
   ** SET UP MENU **
CAMERA ID       1.34..7.
              1 CAMERA
AUDIO SELECT    1
TIMING SELECT   INT
SEQ TIME ADJ    1SEC
PAGE SEQ        2SEC
ALARM REC MODE  FRAME
ALARM TIME ADJ  10SEC BZ
AUTO RESET      OFF
BRIGHT COMP     12..5..8
  END   SET UP ENABLE
   ** SET UP MENU **
CAMERA ID       1.34..7.
              2 CAMERA
AUDIO SELECT    1
TIMING SELECT   INT
SEQ TIME ADJ    1SEC
PAGE SEQ        2SEC
ALARM REC MODE  FRAME
ALARM TIME ADJ  10SEC BZ
AUTO RESET      OFF
BRIGHT COMP     12..5..8
  END   SET UP ENABLE
Press the Down Switch (
C).
Press the Setup Switch.
After completing the selection,
press the Setup Switch.
Press the Right Switch (
B).
■
Setting Procedures
1. Camera Identification Setting (CAMERA ID)
Press the SET UP switch.
Press the Down switch (
C).
After completing the selection,
press the SET UP switch.
Press the Right switch (
B).
Characters can be selected using the Up (
D) or Down  switch (C).
Column can be selected using the Left (
A) or Right switch (B).
After selecting them, press the SET UP switch.
To select 
"
CAMERA ID
"
of other camera, press the Left (
A) or
Right switch (
B).
2. Audio Selection (AUDIO SELECT)
0 1 2 3 4 5 6 7 8 9 : ; A B C D E F G H I J K L M N
O P Q R S T U V W X Y Z Ä Ü Ö Æ Ñ Å Ø " # ' ( )
∗
+ , - . / 
←
= 
→
. (blank)
SEQ/VTR
QUAD/SPOT
TIMING
SELECT
MONITOR
MODE
INT
Picture to be displayed:
changes frame by frame.
Audio output: can be
selected from approx. 1-
30 sec.
Picture to be displayed:
can be selected from
approx. 1-30 sec.
Audio output: changes
with the same time as the
picture.
Picture to be displayed:
changes with the timing
you set on the time lapse
VTR.
Audio output: changes
with the timing you set on
the time lapse VTR.
Picture to be displayed:
changes at the time set on
the time lapse VTR.
Audio output: changes at
the time set on the time
lapse VTR.
EXT