Manualsbrain.com
  1. Manuals
  2. Brands
  3. Panasonic
  4. wv-cm146
  5. User Manual

Panasonic wv-cm146 User Manual

Download
Page of 22
-11-
1
2
3
4
1
2
3
4
“
BRIGH COMP
”
ON
OFF
OFF
ON
  ** SET UP MENU **
CAMERA ID       1.34..7.
              1 CAMERA
AUDIO SELECT    1
TIMING SELECT   EXT
SEQ TIME ADJ    -----
PAGE SEQ        2SEC
ALARM REC MODE  FRAME
ALARM TIME ADJ  10SEC BZ
AUTO RESET      OFF
BRIGHT COMP     1..4....
  END   SET UP ENABLE
Caution:
This function only works on the screen in quad or
sequential mode.
Video signals with compensated brightness will
not be supplied from the REC OUT connector.
While watching reproduced pictures, adjust them
with BRIGHT or CONTRAST control on the front
panel.
9. Bright Compensation (BRIGHT COMP)
9-1. Move the cursor to 
"
BRIGHT COMP.
"
9-2. The desired camera can be selected using the Left
(
A) or Right switch (B).
9-3. Bright Compensation On/Off mode can be selected
using the SET UP switch.
This function provides suitable picture conditions in
quad or sequential mode.
OPERATING PROCEDURES
■
Selection of Camera
CAMERA
VTR
INPUT
SELECT
ON
STAND BY
DISPLAY
MODE
COLOUR
BRIGHT
CONTRAST
PICTURE
AUDIO
MONITOR
MODE
SEQ/VTR
QUAD/SPOT
V-HOLD
MIN.
.MAX
ON
OFF
POWER
QUAD
SEQUENCE 1/5
2/6
3/7
4/8
SET UP
1
2
3, 4
1.
Press the POWER switch on the monitor to turn it on.
2.
Set the INPUT SELECT switch to "CAMERA."
3.
Press the Camera Selection Switch to select the
desired camera picture.
4.
Press the Camera Selection switch once again to dis-
play the camera picture 5, 6, 7, or 8. Two pictures will
be displayed alternately if this switch is pressed
repeatedly.
Caution:
When the POWER switch on the monitor is turned on
and off repeatedly in a short period of time, the camera
may not be turned on due to the protection circuit for
misconnection.
In this case, leave the switch at "OFF" for a few sec-
onds before turning on again.
When power is turned on, no camera picture appears
for a minute because of initializing.
"VD2 SET UP" appears on the display to show the set-
ting process.
■
Quad Mode Monitoring
1.
Press the POWER switch on the monitor to turn it on.
2.
Set the DISPLAY MODE switch to "ON."
3.
Set the INPUT SELECT switch to "CAMERA."
4.
Set the MONITOR MODE switch to "QUAD/SPOT".
Quad picture will be displayed.
5.
By pressing the QUAD/SEQUENCE, SET UP switch,
page A (camera 1-4) and page B (camera 5-8) are dis-
played alternately.
Note:
The screen is totally black without a picture if no
video signal is present at the CAMERA INPUT connec-
tor.
CAMERA
VTR
INPUT
SELECT
ON
STAND BY
DISPLAY
MODE
COLOUR
BRIGHT
CONTRAST
PICTURE
AUDIO
MONITOR
MODE
SEQ/VTR
QUAD/SPOT
V-HOLD
MIN.
.MAX
ON
OFF
POWER
QUAD
SEQUENCE 1/5
2/6
3/7
4/8
SET UP
1
4
3
2
   ** SET UP MENU **
CAMERA ID       1.34..7.
              1 CAMERA
AUDIO SELECT    1
TIMING SELECT   EXT
SEQ TIME ADJ    ----
PAGE SEQ        2SEC
ALARM REC MODE  FRAME
ALARM TIME ADJ  10SEC BZ
AUTO RESET      OFF
BRIGHT COMP     12..5..8
  END   SET UP ENABLE
8-1. Move the cursor to "AUTO RESET."
8-2. Set the Automatic Reset On or Off by using the Left
(
A) or Right switch (B).
8. Automatic Reset On/Off Setting (AUTO
RESET)