Siemens MC35 User Manual
AT Command Set
MC35_ATC_01_V05.00
Page 98 of 256
15.07.2002
4.26 AT+CMER Mobile equipment event reporting
Test command
AT+CMER=?
Response
+CMER: (list of supported <mode>s),(list of supported <keyp>s),(list of supported
<disp>s),(list of supported <ind>s),(list of supported <bfr>s)
<disp>s),(list of supported <ind>s),(list of supported <bfr>s)
Parameters
See write command
Read command
AT+CMER?
Response
+CMER: <mode>,<keyp>,<disp>,<ind>,<bfr>
Parameters
See write command
Write command
AT+CMER=
[<mode>
[,<keyp>
[,<disp> [,<ind>
[,<bfr>]]]]]
[<mode>
[,<keyp>
[,<disp> [,<ind>
[,<bfr>]]]]]
The Execute command enables and disables the presentation of Unsolicited Re-
sult Codes for event reporting. MC35 supports only the type +CIEV (indicator
event reporting). If enabled the +CIEV URCs are sent whenever the value of an
indicator changes.
sult Codes for event reporting. MC35 supports only the type +CIEV (indicator
event reporting). If enabled the +CIEV URCs are sent whenever the value of an
indicator changes.
Response
OK
Parameters
<mode>
0
Discard CIEV Unsolicited Result Codes
1
Discard CIEV Unsolicited Result Codes when TA-TE link is
reserved (e.g. in on-line data mode); otherwise forward them
directly to the TE
reserved (e.g. in on-line data mode); otherwise forward them
directly to the TE
2
Buffer CIEV Unsolicited Result Codes in the TA when TA-TE
link is reserved (e.g. in on-line data mode) and flush them to
the TE after reservation. Otherwise forward them directly to the
TE.
link is reserved (e.g. in on-line data mode) and flush them to
the TE after reservation. Otherwise forward them directly to the
TE.
3
Forward CIEV Unsolicited Result Codes directly to the TE; TA-
TE link specific inband technique used to embed result codes
and data when TA is in on-line data mode
TE link specific inband technique used to embed result codes
and data when TA is in on-line data mode
<keyp>
0
No keypad event reporting
<disp>
0
No display event reporting
<ind>
0
No indicator event reporting
2
Indicator event reporting using result code
+CIEV: <desc>,<value>
<desc> indicates the indicator’s name and <value> is the new
value of this indicator. All indicator events shall be directed
from TA to TE.
+CIEV: <desc>,<value>
<desc> indicates the indicator’s name and <value> is the new
value of this indicator. All indicator events shall be directed
from TA to TE.
<bfr>
0
TA buffer of Unsolicited Result Codes defined within this
command; is cleared when <mode> 1...3 is entered
command; is cleared when <mode> 1...3 is entered
Unsolicited Result Code:
+CIEV: <desc>,<value>
Parameters
<descr> values and their <value> ranges:
"battchg"
Battery charge level (0-5),
where (0-5) means 0, 20, 40, 60, 80 or 100 per
cent of the the remaining battery capacity. If no
battery is connected to the ME, then the value will
be always equal to 5. See also Chapter 8.5.
where (0-5) means 0, 20, 40, 60, 80 or 100 per
cent of the the remaining battery capacity. If no
battery is connected to the ME, then the value will
be always equal to 5. See also Chapter 8.5.