Yamaha htr-5890 User Manual
67
REMOTE CONTROL FEATURES
A
D
V
ANCED
OPERA
T
ION
2
Press an input selector button to select the
source component you want to set up.
source component you want to set up.
3
Press and hold LEARN for about 3 seconds
using a ballpoint pen or similar object.
using a ballpoint pen or similar object.
The library name (ex. “L:DVD”) and the selected
component name (ex. “DVD”) appear alternately in
the display window.
component name (ex. “DVD”) appear alternately in
the display window.
y
If you want to setup for another component, press the input
selector button or SELECT k/n to select the component.
selector button or SELECT k/n to select the component.
• Be sure to press and hold LEARN for at least 3 seconds,
otherwise the learning process will start.
• If you do not complete each of the following steps within
30 seconds, the setting mode will be automatically
canceled. In this case, press LEARN again.
canceled. In this case, press LEARN again.
If you want to change a library (component
category), press
category), press
l
/
h
. You can set a
different type of component.
Library choices: L:DVD, L:DVR, L:LD, L:CD,
L:CDR, L:MD, L:TAP (tape), L:TUN (tuner),
L:AMP
L:CDR, L:MD, L:TAP (tape), L:TUN (tuner),
L:AMP
*
, L:TV, L:CAB (cable), L:SAT (satellite),
L:VCR
*
The amplifier library (L:AMP) code is preset to “AMP1”
(2000) in order to operate this unit. However, you can
switch by entering one of the following five codes if
necessary.
(2000) in order to operate this unit. However, you can
switch by entering one of the following five codes if
necessary.
4
Press ENTER.
The four-digit code set for the selected component
appears in the display window.
appears in the display window.
“0000” appears in the display window if no code has been
set.
set.
5
Press the numeric buttons to enter the four-
digit remote control code for the component
you want to use.
digit remote control code for the component
you want to use.
For a complete list of available remote control codes,
refer to “LIST OF REMOTE CONTROL CODES” at
the end of this manual.
refer to “LIST OF REMOTE CONTROL CODES” at
the end of this manual.
6
Press ENTER to set the number.
“OK” appears in the display window if setting was
successful.
“NG” appears in the display window if the setting
was unsuccessful. In this case, start over from step 3.
successful.
“NG” appears in the display window if the setting
was unsuccessful. In this case, start over from step 3.
y
If you continuously want to set up another code for another
component, press the input selector button or SELECT k/n
to select the component, then repeat steps 4 through 6.
component, press the input selector button or SELECT k/n
to select the component, then repeat steps 4 through 6.
7
Press LEARN again to exit from the setup
mode.
mode.
Notes
Function
Code
AMP1
To operate this unit.
2000
AMP1Z
To operate
ZONE 2
or
ZONE 3
features.
2001
NO
To operate other manufacturers’
receivers / amplifiers using this
unit’s remote control
receivers / amplifiers using this
unit’s remote control
2004
DTV
DVR/VCR2
VCR 1
DVD
V-AUX
CBL/SAT
MD/TAPE
CD-R
PHONO
TUNER
CD
MULTI CH IN
SLEEP
INPUT MODE
A
B
LEARN
Note
THX
STANDARD
EXTD. SUR
ENTERTAIN
MUSIC
TY THTR
MOVIE
STEREO
HALL
JAZZ
ROCK
3
4
2
1
9
0
+10
ENT.
5
6
7
8
LEARN
01EN00_HTR5890U.book Page 67 Thursday, December 23, 2004 12:39 PM