Yamaha RX-V1900BL User Manual
30
En
This unit employs the YPAO (Yamaha Parametric room Acoustic Optimizer) technology which lets you avoid
troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied
optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening
environment. In addition, the multi-point measurement feature enables you to optimize the setup of this unit for up to
eight listening positions.
troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied
optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening
environment. In addition, the multi-point measurement feature enables you to optimize the setup of this unit for up to
eight listening positions.
1
Make sure of the following check points
before starting the automatic setup
operations.
❏ Speakers are connected appropriately.
before starting the automatic setup
operations.
❏ Speakers are connected appropriately.
❏ Headphones are disconnected from this unit.
❏ This unit is turned on.
❏ The connected subwoofer is turned on and the
volume level is set to about half way (or slightly
less).
less).
❏ The crossover frequency controls of the
connected subwoofer is set to the maximum.
❏ The room is sufficiently quiet.
❏ Set the operation mode selector on the remote
control to EAMP.
• Be advised that it is normal for loud test tones to be output
during the automatic setup procedure.
• To achieve the best results, make sure the room is as quiet as
possible while the automatic setup procedure is in progress. If
there is too much ambient noise, the results may not be
satisfactory.
there is too much ambient noise, the results may not be
satisfactory.
2
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
to the OPTIMIZER MIC jack on the front
panel.
“MIC ON View OSD MENU” appears in the front
panel display and the “AUTO SETUP” screen
appears on the video monitor.
panel display and the “AUTO SETUP” screen
appears on the video monitor.
y
You can also run “AUTO SETUP” using the system menu
that appears in the OSD or in the front panel display. This
manual uses the OSD illustrations to explain the automatic
setup procedure.
that appears in the OSD or in the front panel display. This
manual uses the OSD illustrations to explain the automatic
setup procedure.
3
Start the automatic setup.
To optimize the setup of this unit for one listening
position, follow “Basic automatic setup” (page 30).
To optimize the setup of this unit for multiple
listening positions, follow “Advanced automatic
setup” (page 33).
To optimize the setup of this unit for one listening
position, follow “Basic automatic setup” (page 30).
To optimize the setup of this unit for multiple
listening positions, follow “Advanced automatic
setup” (page 33).
If you have done all the preparations necessary, follow the
procedure below to optimize the setup of this unit for one
listening position.
procedure below to optimize the setup of this unit for one
listening position.
1
Place the optimizer microphone at your
normal listening position on a flat level
surface with the omni-directional
microphone heading upward.
normal listening position on a flat level
surface with the omni-directional
microphone heading upward.
Optimizing the speaker setting for your listening room
Before starting the automatic
setup
setup
Notes
VOLUME
MIN
MAX
MIN
MAX
CROSSOVER
HIGH CUT
Controls of a subwoofer (example)
INFO
ZONE ON/OFF
ZONE CONTROLS
MULTI ZONE
MIC
OPTIMIZER
EFFECT
PROGRAM
YPAO
ZONE 3
R
L
OPTICAL
ZONE 2
AUDIO
VIDEO AUX
SILENT CINEMA
S VIDEO
VIDEO
PHONES
BAND
CATEGORY
PRESET/TUNING/CH
MONO
STEREO/
MODE
SEARCH
MEMORY
STRAIGHT
CONTROL
SELECT
AUDIO
TONE
ENTER
Omni-directional
microphone
microphone
Basic automatic setup
[]/[]:
[ENTER]:
[ENTER]:
[
p
AUTO SETUP
SETUP;;;;;;;;;AUTO
MULTI MEASURE;;;;1
START
Up/Down
Start
.
Optimizer microphone