Eton elite e10 User Manual

Page of 80
E 1 0
O P E R A T I O N   M A N U A L
7
6
5
GETTING STARTED
W H AT   T H E   E 1 0   I N C L U D E S  
• Earbud style earphones
• Carrying pouch
• AC adaptor/charger
• 4 - 1100 mAh, Ni-MH rechargeable batteries.
• Owner’s manual
NOTE: In the instructions below, numbers in
parenthesis ( ), refer to the diagrams.
I N S TA L L I N G   B AT T E R I E S  
The battery compartment is located on the back of
the E10. Its cover is on the lower right corner of the
back. To remove the battery compartment cover,
apply thumb pressure and slide it towards the bottom
of the radio. Install 4 AA alkaline batteries into the
battery compartment, observing the battery polarity
diagram on the back of the radio.
NOTE: If you don’t plan to use rechargeable bat-
teries at all, then it’s a good idea to set SYSTEM SET
CODE 29. To do this, see the section titled SYSTEM
SET CODES. This assures that the battery strength
indicator will display correctly for your non-
rechargeable batteries. This is not a mandatory 
procedure and the E10 will function if it is not done.
P R E V E N T I N G   B AT T E RY   A C I D
L E A K A G E  
To avoid battery acid leakage, only use high quality
alkaline, lithium or rechargeable nickel-metal-
hydride batteries. Never intermix old with new, or
different brands or types of batteries. Damage
caused by battery acid leakage is not covered by
this product’s warranty. If the batteries leak, don’t
throw them away and immediately contact the
manufacturer of the batteries to inquire about their
battery leakage warranty program.
U S I N G   T H E   I N C L U D E D   A C
A D A P T O R / C H A R G E R
To power the E10 with the included AC Adaptor/
Charger, plug it into a wall outlet first, and then
into the socket on the left side of the E10, labeled
DC 6 V. Batteries can be in the radio while using
the AC Adaptor/Charger.
C H A R G I N G   B AT T E R I E S   I N   T H E
E 1 0
The E10 will play using whatever type of AA batteries
are in the battery compartment, but only nickel-
metal-hydride batteries can be charged within it. If
non-rechargeable batteries are installed, the E10
has a built-in safeguard system that will prevent
them from being charged. This safeguard system
works with the E10 set to either SYSTEM SET
CODE 28 or 29, as described below, and only with
the included AC Adaptor/Charger.
WARNING: Use only the included AC
Adaptor/Charger to recharge Ni-MH batteries. Use
of any other device may cause the rechargeable
batteries to overheat, become damaged and possibly
damage the E10. The built-in safeguard system,
described above, works only with the included AC
Adaptor/Charger. Damage caused to the E10
resulting from failure to observe this warning is not
covered by the warranty and voids the warranty.
DIAGRAMS 
continued
Triangle Pointer
Battery Symbol
Ni-MH Battery Symbol
Time AM/PM Indicator
Delete Indicator
Memory Display
Shortwave Meter Band Display
Clock Digits
Alarm Activation Symbol
FM, MW,
Shortwave 
Indicators
Alarm 
Clock 
Digits
Alarm AM/PM Indicator
Antenna Symbol
1-5 Scale
Triangle Pointer
Battery Symbol
Clock Digits
Alarm
Activation
Symbol
Antenna Symbol
Frequency Digits
450K IF
Bandwidth
1-5 Scale
Sleep Timer Symbol
R A D I O   O F F   D I S P L AY
R A D I O   O F F   D I S P L AY
R A D I O   O N   D I S P L AY
M E M O RY   D I S P L AY
Refers only the the display’s upper right corner.
S Y S T E M   S E T   C O D E   D I S P L AY
SHORTWAVE METER BAND DISPLAY
Refers only the the display’s upper right corner.