Sharp dv-rw2u User Manual

100

EDIT

OPEN/
CLOSE

POWER

SKIP

AUDIO

TIMER

ON/OFF

TITLE

ANGLE

SETUP/

FUNCTION

DNR

RETURN

REV

FWD

SET/

ENTER

VCR PLUS+

TIMER PROG.

REC MODE

PROGRAM

AM/PM

ERASE

STILL/PAUSE

REC

PLAY

STOP

SLOW

SKIP

F.ADV

ORIGINAL/
PLAY LIST

DISC

TIMER

DISPLAY

SCREEN

POWER

INPUT

VOL

TV CONTROL

ZOOM

INPUT

Operating a TV Using the
Remote Control
(Universal Remote Control)

The Universal Remote Control may operate the
basic functions of 21 different types of TVs.
To enter the Manufacturer’s Code for your TV,
follow the instructions below.

There is no guarantee that the universal
remote control will function with your TV.

Setting the
Manufacturer’s Code

Press POWER and CH ' of TV

CONTROL simultaneously.

Enter the 2-digit Manufacturer’s

Code with the number buttons

(Ex. 02-“0”, “2”) within 10

seconds after releasing POWER

and CH ' of TV CONTROL.

Point the remote control unit

towards the TV and then press

POWER of TV CONTROL.

• If the TV turns on/off, setup was

successful. If not, repeat the proce-
dure using another code.

Refer to the list below for the Manufacturer’s Code
and the buttons which work with each brand.

Major Components

Setting the Remote
Control Code

• There are two types of codes (remote

control codes) for operating this recorder
with the remote control (RC1 and RC2). If
you operate this recorder with the remote
control while using with another SHARP
DVD recorder or DVD player placed next to
it and both units end up being operated
simultaneously, switching the remote control
code (for both the recorder and the remote
control) to one of the two signals (RC1 or
RC2) will let you operate only the recorder.

• Make sure to set the recorder and remote

control to the same remote control code.
You will not be able to operate the recorder
with the remote control if different remote
control codes are used.

Important!

If the remote control codes of the recorder
and remote control are different, the remote
control code will flash on the display of the
recorder. Reset the remote control number
to the code flashing on the display.

Note

• The remote control code of the remote become

“RC 1” when you change the batteries.

Setting the Remote
Control Code of the
Recorder

Press POWER to turn off the

recorder.

Press and hold CHANNEL" and
' on the recorder together for
more than 5 seconds.

• Each time the button is pressed, the

code of the recorder toggles between
“RC-1” and “RC-2”.

• At this point, the recorder can no

longer be operated with the remote
control. Next, set the remote control
code for the remote control.

Setting the Remote
Control Code of the
Remote

Example: Setting the “RC2”.

Press and hold POWER and 2

together for more than 5 seconds.

• When you set the code to “RC1”, press

and hold POWER and 1 together.

The recorder is turned on.

Brand

EMERSON

FISHER

FUNAI

GOLDSTAR

HITACHI

JVC

MAGNAVOX

MITSUBISHI

PANASONIC

PIONEER

RCA

SAMSUNG

SANYO

SHARP

SONY

TECHNOL ACE

TOSHIBA

ZENITH

Code

19
17
06

07, 09

18
15
16
09
11
14

13, 21

07, 09

20
17
01
02
10
04
12
05
08

POWER

CH '

'/"

VOL

INPUT

—
—

—

Buttons on the Remote

NOTE

• If the batteries in the remote control unit are

changed, the code settings must be re-entered.

• Some brands have more than one code

listed above, due to changes in the codes.
In such cases, try another code to find the
code that operates your TV.

DV_RW2U#p12-18.p65

03.1.14, 9:17 AM