heatcraft-refrigeration-p h-im-fl1a User Manual

General Safety Information

1. Installation and maintenance to be performed only by

qualiﬁed personnel who are familiar with this type of

equipment.

2. Some units are pressurized with dry air or inert gas. All units

must be evacuated before charging the system with refrigerant.

3. Make sure that all ﬁeld wiring conforms to the requirements

of the equipment and all applicable national and local codes.

4. Avoid contact with sharp edges and coil surfaces. They are

a potential injury hazard.

5. Make sure all power sources are disconnected before any

service work is done on units.

WARNING:

Refrigerant can be harmful if it is inhaled. Refrigerant must be used and recovered

responsibly. Failure to follow this warning may result in personal injury or death.

Inspection

Responsibility should be assigned to a dependable individual at

the job site to receive material. Each shipment should be carefully

checked against the bill of lading. The shipping receipt should

not be signed until all items listed on the bill of lading have been

accounted. Check carefully for concealed damage. Any shortage

or damages should be reported to the delivering carrier. Damaged

material becomes the delivering carrierʼs responsibility, and should

not be returned to the manufacturer unless prior approval is

given to do so. When uncrating, care should be taken to prevent

damage. Heavy equipment should be left on its shipping base

until it has been moved to the ﬁnal location. Check the serial tag

information with invoice. Report any discrepancies to your Heatcraft

Refrigeration Products Sales Representative.

Warranty Statement

eller warrants to its direct purchasers that products, including

Service Parts, manufactured by SELLER shall be of a merchantable

quality, free of defects in material or workmanship, under normal

use and service for a period of one (1) year from date of original

installation, or eighteen (18) months from date of shipment by

SELLER, whichever ﬁrst occurs. Any product covered by this order

found to Sellerʼs satisfaction to be defective upon examination at

Sellerʼs factory will at SELLERʼs option, be repaired or replaced

and returned to Buyer via lowest common carrier, or SELLER

may at its option grant Buyer a credit for the purchase price of the

defective article. Upon return of a defective product to SELLERʼs

plant, freight prepaid, by Buyer, correction of such defect by repair

or replacement, and return freight via lowest common carrier, shall

constitute full performance by SELLER of its obligations hereunder.

SELLER shall have no liability for expenses incurred for repairs

made by Buyer except by prior, written authorization. Every claim

on account of breach of warranty shall be made to SELLER in

writing within the warranty period speciﬁed above – otherwise

such claim shall be deemed waived. Seller shall have no warranty

obligation whatsoever if its products have been subjected to

alteration, misuse, negligence, free chemicals in system, corrosive

atmosphere, accident, or if operation is contrary to SELLERʼs or

manufacturerʼs recommendations, or if the serial number has been

altered, defaced, or removed.

MOTOR COMPRESSORS:

Motor compressors furnished by SELLER are subject to the

standard warranty terms set forth above, except that motor

compressor replacements or exchanges shall be made through

the nearest authorized wholesaler of the motor compressor

manufacturer (not at SELLERʼs factory) and no freight shall be

allowed for transportation of the motor compressor to and from the

wholesaler. The replacement motor compressor shall be identical

to the model of the motor compressor being replaced. Additional

charges which may be incurred throughout the substitution of

other than identical replacements are not covered by this warranty.

An optional, nonassignable, four (4) year extended compressor

warranty may be purchased within the boundaries of the United

Sates of America, its territories and possessions, and Canada. With

this extended compressor warranty, replacements are administered

by an authorized compressor distributor only. Replacements within

the ﬁrst year of the warranty area available through the distributor;

the second through ﬁfth years, the purchaser must submit a proof-

of-purchase of a compressor and supply it to Heatcraft Refrigeration

Products Warranty Claims for reimbursement.

Seller makes no express warranties except as noted above.

All implied warranties are limited to the duration of the Express

Warranty. Liability for incidental and consequential damages is

excluded.

The forgoing is in lieu of all other warranties, express or implied,

notwithstanding the provisions of the uniform commercial code, the

Magnuson-Moss Warranty-Federal Trade Commission Improvement

Act, or any other statutory or common law, federal or state.

SELLER makes no warranty, express or implied, of ﬁtness for

any particular purpose, or of any nature whatsoever, with respect

to products manufactures or sold by seller hereunder, except as

speciﬁcally set forth above and on the face hereof. It is expressly

understood and agreed that SELLER shall not be liable to buyer,

or any customer of buyer, for direct or indirect, special, incidental,

consequential or penal damages, or for any expenses incurred

by reason of the use or misuse by buyer or third parties of said

products. To the extent said products may be considered "consumer

products," As deﬁned in Sec. 101 of the Magnuson-Moss Warranty

- Federal Trade Commission Improvement Act, SELLER makes no

warranty of any kind, express or implied, to "consumers," except as

speciﬁcally set forth above and on the face hereof.

The following conditions should be adhered to when installing this

unit to maintain the manufacturers warranty:

(a) System piping must be in accordance with good

refrigeration practices.

(b) Inert gas must be charged into the piping during

brazing.

(c)

The power supply to the unit must meet the

following conditions:

A. Three phase voltages must be +/-

10% of nameplate ratings. Single

phase must be within +10% or

-5% of nameplate ratings.

B. Phase imbalance cannot exceed 2%.

(d) All control and safety switch circuits must be

properly connected according to the wiring diagram.

(e) The factory installed wiring must not be changed

without written factory approval.

(f)

All equipment is installed in accordance with

Heatcraft speciﬁed minimum clearances.