Panasonic KXMC6260E Operating Guide
Important Information
3
Important Information
Important Information
For your safety
Laser radiation
Fuser unit
Note:
L
The left side of the unit (
2) and the area near the
recording paper exit (
3) also get warm. This is
normal.
For best performance
Toner cartridge and drum cartridge
L
When replacing the toner cartridge or drum
cartridge, do not allow dust, water, or liquids to come
in contact with the drum. This may affect print quality.
cartridge, do not allow dust, water, or liquids to come
in contact with the drum. This may affect print quality.
L
For optimal performance, genuine Panasonic toner
cartridges and drum cartridges are recommended.
We cannot be responsible for problems that may be
caused by a non-Panasonic toner cartridge or drum
cartridge:
cartridges and drum cartridges are recommended.
We cannot be responsible for problems that may be
caused by a non-Panasonic toner cartridge or drum
cartridge:
–
Damage to the unit
–
Poor print quality
–
Improper operation
Toner cartridge
L
Do not leave the toner cartridge out of the protection
bag for a long time. It will decrease the toner life.
bag for a long time. It will decrease the toner life.
Drum cartridge
L
Read the instructions on page 12 before you begin
installation of the drum cartridge. After you have read
them, open the drum cartridge protection bag. The
drum cartridge contains a photosensitive drum.
Exposing it to light may damage the drum. Once you
have opened the protection bag:
–
installation of the drum cartridge. After you have read
them, open the drum cartridge protection bag. The
drum cartridge contains a photosensitive drum.
Exposing it to light may damage the drum. Once you
have opened the protection bag:
–
Do not expose the drum cartridge to light for
more than 45 seconds.
more than 45 seconds.
–
Do not touch or scratch the green drum surface.
–
Do not place the drum cartridge near dust or dirt,
or in a high humidity area.
or in a high humidity area.
–
Do not expose the drum cartridge to direct
sunlight.
sunlight.
L
To extend the life of the drum cartridge, the power
switch should never be turned OFF immediately after
printing. Leave the power turned ON for a minimum
of 30 minutes after printing.
switch should never be turned OFF immediately after
printing. Leave the power turned ON for a minimum
of 30 minutes after printing.
Location
L
To avoid malfunction, do not position the unit near
appliances such as TVs or speakers which generate
an intense magnetic field.
appliances such as TVs or speakers which generate
an intense magnetic field.
Static electricity
L
To prevent static electricity damage to the interface
connectors or other electrical components inside the
unit, touch a grounded metal surface before touching
the components.
connectors or other electrical components inside the
unit, touch a grounded metal surface before touching
the components.
Environment
L
Keep the unit away from electrical noise generating
devices, such as fluorescent lamps and motors.
devices, such as fluorescent lamps and motors.
L
The unit should be kept free from dust, high
temperature and vibration.
temperature and vibration.
L
The unit should not be exposed to direct sunlight.
L
Do not place heavy objects on top of the unit. When
you leave the unit unused for a long period of time,
unplug this unit from the power outlet.
you leave the unit unused for a long period of time,
unplug this unit from the power outlet.
L
The unit should be kept away from heat sources such
as heaters, kitchen stoves, etc. Damp basements
should also be avoided.
as heaters, kitchen stoves, etc. Damp basements
should also be avoided.
L
In the printing process, heat is used to fuse toner
onto the page. As a result, it is normal for the
machine to produce an odour during and shortly after
printing. Be sure to use this unit in an area with
proper ventilation.
onto the page. As a result, it is normal for the
machine to produce an odour during and shortly after
printing. Be sure to use this unit in an area with
proper ventilation.
L
Do not place any objects within 10 cm of the right, left
and back sides of the unit.
and back sides of the unit.
CLASS 1 LASER PRODUCT
The printer of this unit utilises a laser. Use of
controls or adjustments or performance of
procedures other than those specified
herein may result in hazardous radiation
exposure.
controls or adjustments or performance of
procedures other than those specified
herein may result in hazardous radiation
exposure.
Laser diode properties
Laser output : Max. 6.5 mW
Wavelength : 770 nm – 800 nm
Emission duration : Continuous
Laser output : Max. 6.5 mW
Wavelength : 770 nm – 800 nm
Emission duration : Continuous
During or immediately after printing, the
fuser unit (
fuser unit (
1) gets hot. This is normal. Do
not touch the fuser unit.
1
2
3