Panasonic KXTGD325E Operating Guide
Important:
R Make sure the unit’s date and time setting
R Make sure the unit’s date and time setting
is correct (page 15).
R We recommend turning the base unit ringer
R If you have set the alarm, the alarm sounds
even if do not disturb mode is turned on.
Turning do not disturb mode on/off
1
MMENUN#238
2
MbN: Select the desired setting. a MOKN
R If you select “Off”, press MOFFN to
R If you select “Off”, press MOFFN to
exit.
3
Enter the desired hour and minute you
wish to start this feature. a MOKN
wish to start this feature. a MOKN
4
Enter the desired hour and minute you
wish to end this feature. a MOKN a
MOFFN
wish to end this feature. a MOKN a
MOFFN
Changing the start and end time
1
MMENUN#237
2
Setting the ring delay
This setting allows the handset to ring during
do not disturb mode if the caller waits long
enough. After the selected amount of time
passes, the handset rings. If you select “No
Ringing”, the handset never rings during do
not disturb mode.
do not disturb mode if the caller waits long
enough. After the selected amount of time
passes, the handset rings. If you select “No
Ringing”, the handset never rings during do
not disturb mode.
1
MMENUN#239
2
MbN: Select the desired setting. a MOKN
a MOFFN
a MOFFN
Note:
R When the answering system answers the
R When the answering system answers the
call, this feature does not work.
(KX-TGD320 series: page 3)
(KX-TGD320 series: page 3)
Selecting categories to bypass do
not disturb mode
not disturb mode
1
MMENUN#241
2
MbN: Select the desired categories. a
MSELECTN
R “ ” is displayed next to the selected
MSELECTN
R “ ” is displayed next to the selected
category numbers.
R To cancel the selected category:
MbN: Select the category. a Press
MSELECTN again. “ ” disappears.
MSELECTN again. “ ” disappears.
3
MOKN a MOFFN
Nuisance call block
This feature blocks calls from unwanted
callers (Caller ID subscribers only). The
following items are available when storing
phone numbers in the call block list (50 max.).
– “Single Number”: The unit blocks calls
callers (Caller ID subscribers only). The
following items are available when storing
phone numbers in the call block list (50 max.).
– “Single Number”: The unit blocks calls
from specific phone numbers.
– “Range of Numbers”: The unit blocks
calls that begin with a number stored in the
call block list, such as a toll-free phone
number prefix or certain area codes.
call block list, such as a toll-free phone
number prefix or certain area codes.
You can also set the unit to block calls that
have no phone number.
When a call is received, the unit does not ring
while the caller is being identified. If the
caller’s phone number matches an entry in the
call block list, the unit emits no sound to the
caller, and disconnects the call.
Important:
R Blocked calls are logged in the caller list.
have no phone number.
When a call is received, the unit does not ring
while the caller is being identified. If the
caller’s phone number matches an entry in the
call block list, the unit emits no sound to the
caller, and disconnects the call.
Important:
R Blocked calls are logged in the caller list.
Storing unwanted callers
Storing a single phone number
Important:
R You must include the area code when
R You must include the area code when
storing phone numbers in the call block list.
n
From the caller list:
1
MCN CID
2
MbN: Select the entry to be blocked. a
MMENUN
MMENUN
3
MbN: “Save Call Block” a MOKN
4
MbN: “Yes” a MOKN a MOFFN
n
By entering phone numbers:
1
MMENUN#217
30
Helpline Tel. No.: U.K. 0844 844 3899 Ireland 01289 8333
Programming
TGD31x_32xE(en)0202_ver201.pdf 30
2015/02/02 14:00:40