Panasonic SC-ZT1 Operating Guide
RQT9472
16
When the speakers are detected, the Wireless Link display lights up on the main unit’s
display.
(Blinks during detecting operation.)
While the wireless speakers operate normally, the Wireless Link display lights, but when radio
waves are interrupted (when speakers are in standby condition, etc.), it blinks.
display.
(Blinks during detecting operation.)
While the wireless speakers operate normally, the Wireless Link display lights, but when radio
waves are interrupted (when speakers are in standby condition, etc.), it blinks.
Display
W
Wireless Link
display
display
Speaker setting
• When you turn the main unit off with the speakers on, the speakers automatically enter standby (Wireless link standby). The
colour of [WIRELESS LINK] indicator turns to red.
• To reduce more of the power consumption of speakers in standby, turn the speakers off. The speakers enter standby (In standby
condition).
<Power consumption of speakers in standby>
Wireless link standby: approx. 0.8 W (per 1 speaker)
In standby condition: approx. 0.15 W (per 1 speaker)
Wireless link standby: approx. 0.8 W (per 1 speaker)
In standby condition: approx. 0.15 W (per 1 speaker)
Speaker setting
Connection
Checking the speaker setting
1. Turn the main unit on.
2. Press [TEST] on the remote
control to output the test signal.
3. Make sure that the display of main unit matches speaker locations.
The test signal is output from one speaker at a time for about 2 seconds in the order shown below.
“
“
TEST L ”
→ “TEST R ” → “TEST RS ”
✽
→ “TEST LS ”
✽
Confi rm the correct setting locations in the following chart.
Display
Speaker outputting the test signal
TEST L
Front left
TEST R
Front right
TEST RS
✽
Surround right (right back)
TEST LS
✽
Surround left (left back)
If the speakers are not properly set, do either of the following.
• Move the speakers according to the unit’s display.
• Perform steps
• Move the speakers according to the unit’s display.
• Perform steps
3 and 4 of “Setting the speakers” (➜ page 15). When using the surround speakers, perform steps 7 and 8 of
“Setting surround speakers” (➜ page 17).
4. Press [TEST] on the remote control to stop the test signal.
If the speaker is repaired or replaced
Perform the above “Checking the speaker setting” to confi rm that the speaker properly operates.
Do the following operations if the sound is not produced normally.
1. Press and hold [INPUT SELECTOR] on the main unit approx. 3 seconds until “
Perform the above “Checking the speaker setting” to confi rm that the speaker properly operates.
Do the following operations if the sound is not produced normally.
1. Press and hold [INPUT SELECTOR] on the main unit approx. 3 seconds until “
2CH SEARCH ” is displayed.
2. Perform steps
2 to 4 of “Setting the speakers” (➜ page 15).
Installing surround speakers
You can enjoy more dynamic surround playback with this system by installing Panasonic surround speakers SB-ZT1.
Note
✽ Displayed only when using
the surround speakers.
Press
• To adjust the speaker volume, press [VOL +, –].
Setup example
Front speaker
(right)
(right)
Front speaker
(left)
(left)
Connected equipment
Main unit
The surround speakers are not included.
Surround
speaker
(left)
speaker
(left)
Surround
speaker (right)
speaker (right)
Approx. 120°
• Place them slightly at the back right and left of the listening-viewing
position.
• There is no positional distinction for each speaker before setting.
• Aim the front face (with Panasonic logo) of each speaker at the listening-
• Aim the front face (with Panasonic logo) of each speaker at the listening-
viewing position for setting.
Set the distance from each speaker to the listening-viewing
position. (➜ page 24)
position. (➜ page 24)
Note