Riello DLD 600 UM6K600735RUB User Manual

25

Dialog Dual 

 3,3-1

0 kV

A

SIMPLIFIED INSTALLATION
• the uPs can be installed as a floor standing tower or 19” rackmount 
  uPs. the front panel digital display can be pulled out (using the keys 
  provided) and rotated to suit the installation format
• low noise level (<40dBA) thanks to the digitally Pwm controlled
  ventilation system which is load and temperature dependent, and the 
  use of an inverter with a high switching frequency
• optional bolt-on maintenance bypass (dld 5-6-8-10 kVA models) to 
  allow service without disruption to the loads
• Performance guaranteed in temperatures up to 40°c
• two iEc output plugs with thermal protection (dld5-6-8-10 kVA).
• Powershare output socket (2x10A iEc) functionality on dld 5-6-8-10 
  kVA models

SELECTABLE OPERATING MODES
• on line mode (VFi).
• Economy mode: increases efficiency (up to 98%), and uses line 

interactive technology to power low priority loads from the mains 
supply.

• smart mode: the uPs automatically decides which operating mode to 

use (Vi or VFi) depending on the quality of the mains supply.

• Emergency mode: the uPs can be set to operate only when mains 

power fails (emergency only mode).

• Frequency converter mode (50 or 60 hz).

GUARANTEED OUTPUT QUALITY
• Even with typical distorting it loads with crest factors of 3:1
• increased short circuit current on the bypass
• increased overload capacity: 150% on inverter even when mains 
  supply has failed
• reliable, filtered, stabilised and regulated sinewave output 
  (double conversion technology VFi in conformity with iEc 62040-3 
  specifications) with filters for atmospheric disturbance suppression
• rephasing of load as the uPs has an input power factor close to 1, 
  with a sinusoidal input current

HIGHLY RELIABLE BATTERY PERFORMANCE
• Automatic and manual battery tests
• unique low ripple current discharge (lrcd) to help prolong 
  battery life
• hot-swap user replaceable batteries

• unlimited extendable back-up time using modular design Battery 
  Extension Packs
• increased ride through (without batteries) on mains breaks up to 
  40ms and for fluctuations ranging from 84 to 276Vac

OTHER CHARACTERISTICS
• output voltage selection: 220-230-240Vac
• Auto restart when mains power returns - programmed using the uPs 
  tools software supplied
• Bypass on: when the uPs is switched off, it automatically goes into 
  bypass mode to charge the batteries
• Automatic power down due to minimum load 
• End of battery discharge pre-alarm
• delayed start up
• completely digitally controlled
• Automatic bypass with no break in power supply
• use of ims (insulated metallic substrates) modules
• status, measurements, and alarms available on the standard backlit 
  display
• uPs can be updated digitally (flash upgradeable)
• input protected by resettable thermally activated switch
• Back-feed protection: to avoid current being fed back into the mains 
  should a fault occur
• manual switch over to bypass

ADVANCED COMMUNICATION
• Advanced, multi-platform communication for all operating systems 

and network environments: Powershield

3

 monitoring and shut-down 

software included, for windows 2008, Vista, 2003, XP; mac os X, 
linux, Novell and most popular unix operating systems. 

•the uPs is supplied with a communications cable for ‘Plug and Play’ 
  Pc connection
• usB port
• rs232 serial port
• interface card slot

iNPut sockEt

iNtErFAcE cArd slot

sNmP or AdditioNAl

rs232 Ports

outPut sockEts

BAttEry

EXtENsioN PAck 

coNNEctor

sEriAl Port

usB Port

iNPut thErmAl

ProtEctioN rE-sEt

iNPut 

cABlE AccEss

outPut 

cABlE AccEss