Panasonic SC-PM39D Operating Guide
22
RQT7502
Radio operations
The radio
Displaying the text data, the name of a broadcasting station or
a program type.
Press [FL DISPLAY].
Every time you press the button:
a program type.
Press [FL DISPLAY].
Every time you press the button:
Station Name (PS)
Clock
Program Type (PTY)
Note
•
RDS displays may not be available if reception is poor.
\
“M.O.R. M” = “Middle of the road music”
•
Sound is momentarily interrupted if you load or unload tapes while
listening to an AM broadcast.
listening to an AM broadcast.
7
7
7
7
7 AM frequency step (main unit only)
For Saudi Arabia, Kuwait, the Middle East and Southeast Asia only
The step is factory-set to 9 kHz, but you can change it to receive
broadcasts allocated to 10 kHz steps.
1. Select “FM”.
2. Press and hold [TUNER/AUX].
broadcasts allocated to 10 kHz steps.
1. Select “FM”.
2. Press and hold [TUNER/AUX].
After a few seconds the display changes to show the current
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
minimum frequency. Continue to hold the button down. The
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
Note
After changing the “allocation” setting, the frequencies you previously
preset in the memory will be cleared. Preset them again.
preset in the memory will be cleared. Preset them again.
7
7
7
7
7 RDS broadcasting
For the United Kingdom, Continental Europe and Russia only
The unit can display the text data transmitted by the radio data system
(RDS) available in some areas.
If the station you are listening to is transmitting RDS signals, “RDS”
will light up on the display.
(RDS) available in some areas.
If the station you are listening to is transmitting RDS signals, “RDS”
will light up on the display.
Manual tuning
or
FM
AM
AUX
TUNER /
AUX
VOLUME
•
Press and hold [(] or [)] until the frequency starts scrolling to start automatic tuning.
Tuning stops when a station is found.
Tuning stops when a station is found.
“ST” is displayed when a stereo FM broadcast is being received.
If noise is excessive in FM
1. Press [PLAY MODE] to display “MONO”.
2. Press [PLAY MODE] again to cancel the mode.
(The mode is also cancelled when you changed the frequency)
1. Press [PLAY MODE] to display “MONO”.
2. Press [PLAY MODE] again to cancel the mode.
(The mode is also cancelled when you changed the frequency)
Program type displays
NEWS
VARIED
FINANCE
COUNTRY
AFFAIRS
POP M
CHILDREN
NATIONAL
INFO
ROCK M
SOCIAL A
OLDIES
SPORT
M.O.R. M
\
RELIGION
FOLK M
EDUCATE
LIGHT M
PHONE IN
DOCUMENT
DRAMA
CLASSICS
TRAVEL
TEST
CULTURE
OTHER M
LEISURE
ALARM
SCIENCE
WEATHER
JAZZ
1
Select “FM” or
“AM”.
“AM”.
2
Select the
frequency of
the desired
station.
frequency of
the desired
station.
3
Adjust the
volume.
volume.
Preset tuning
Preset channels to make selection simpler. Up to 15 stations can each be set in the FM and AM bands.
Manual presetting
Tune to the desired station (A see above).
PGM
AUDIO
MIC VOL
ECHO
The station occupying a channel is erased if another station is preset
in that channel.
in that channel.
Automatic presetting
Tune to the frequency where pre-setting is to begin (A see above).
PGM
The tuner presets all the stations it can receive into the channels in
ascending order.
When finished, the last station to be set is played.
ascending order.
When finished, the last station to be set is played.
Selecting channels
1. Press [TUNER/AUX] to select “FM” or “AM”.
2. Press the numbered buttons or [g 4/REW] or [f 3 /FF] to
2. Press the numbered buttons or [g 4/REW] or [f 3 /FF] to
select the channel.
1
Press to
select.
select.
(“PGM” will
appear)
appear)
2
Press while the
station is flashing
to select the
channel.
station is flashing
to select the
channel.
Press and hold.
(release when “AUTO”
is displayed)
is displayed)
RQT7502_22_23_new
3/16/04, 2:54 PM
22