Panasonic LQDRM200 Operating Guide
24
Timer recording
Manual programming
[RAM] [DVD-R]
Remote control only
You can set your own programming conditions (up to 16
programmes).
programmes).
Preparation
≥Switch [DVD, TV] (19) to “DVD”.
≥Ensure that this unit’s clock is set correctly.
≥Insert a disc for recording (make sure there is enough room for
≥Switch [DVD, TV] (19) to “DVD”.
≥Ensure that this unit’s clock is set correctly.
≥Insert a disc for recording (make sure there is enough room for
the programme you are going to record plus a little extra).
1
Press [PROG/CHECK]
≥The Timer Programme List screen appears.
A line that is ready for programming is highlighted.
2
(10).
≥The Timer Programme Correction screen appears.
3
Use [
1] (10) to move through the items and change
the items with [
3, 4] (10).
≥The current settings are shown each time you press [1] (10).
≥You may use the numeric buttons (4) to enter “Name”,
≥You may use the numeric buttons (4) to enter “Name”,
“Date”, “Start” and “Stop”.
≥Name (Programme Position/TV Station Name)
≥Date
≥Date
Current date
!)the day before one month later!)
Daily (Sunday to Saturday)
!)Daily (Monday to
Saturday)
!)Daily (Monday to Friday)!)Weekly
(Sundays)
!)…!)Weekly (Saturdays)!)Current date…
≥Start (start time)/Stop (finish time)
The time increases or decreases in 30-minute increments if
you hold the button.
you hold the button.
≥Mode (Recording mode)
XP
!)FR!)EP!)LP!)SP!)XP… (page 19)
≥Title
Select “Title” and press [ENTER]
for entering title.
4
Press [ENTER]
(10) when you have finished making
changes.
≥To continue programming:
Repeat steps 2, 3 and 4.
5
Press [PROG/CHECK]
To put the unit on recording standby
Press [
Ensure “
” lights on the unit’s display.
To change the timer recording programme
1) While the Timer Programme List Screen is being shown, use
[
3, 4] (10) to select the programme you want to change, and
press [ENTER]
(10) to show the Timer Programme Correction
screen.
≥You may also select programme by inputting a 2-digit number
≥You may also select programme by inputting a 2-digit number
using the numeric buttons
≥Use [2, 1] (10) to move to the page preceding or following
the one on display.
2) Move through the items with [
1] (10) and change the settings
with [
3, 4] (10) and press [ENTER] (10).
Note
≥The built-in clock employs 24-hour system.
≥The remaining time is not shown if you insert discs other than
≥The built-in clock employs 24-hour system.
≥The remaining time is not shown if you insert discs other than
DVD-RAM or DVD-R.
≥The remaining time displayed is calculated based on the current
recording mode.
standby but does not go on standby for recording. Check the disc
carefully.
carefully.
≥“PROG FULL” is displayed in the unit’s display if there are already
16 items programmed. Delete unnecessary items (page 25).
≥Recording is not possible unless you set “Disc Protection” in
“DISC INFORMATION” to “Off” (page 28).
≥You cannot record to a disc if the write protect tab on a cartridge
disc is set to protect. Release this before operation (page 61).
≥Even if the unit is put in the timer recording standby mode or the
timer recording is being performed, you can play a programme.
≥When recording more than one programme in a row, for
DVD-RAM the first few seconds, and for DVD-R about the first
30 seconds of all programmes from the second one onwards will
not be recorded.
30 seconds of all programmes from the second one onwards will
not be recorded.
RETURN
SELECT
SP
OK
1:22
1:19
AV1
15/ 7 TUE
01
Mode
Disc
space
Stop
Start
No.
Name
Date
1:58 SP
TIMER
RECORDING
RECORDING
Remain
1:19:00 15.7 TUE
ENTER
New Timer Programme
Press ENTER to store
new programme.
new programme.
RETURN
SELECT
1:58 SP
TIMER
RECORDING
RECORDING
Remain
1:55:00 15.7 TUE
ENTER
--:--
--/-- ---
Mode
Stop
Start
Name
Date
--:--
SP
Please set Input.
Title
1:58 SP
TIMER
RECORDING
Remain
1:19:00 15.7 TUE
2:00
15/ 7 TUE
Mode
Stop
Start
Name
Date
SP
AV1
1:00
Title
E60TEG.book 24 ページ 2003年9月1日 月曜日 午後5時6分