Panasonic KXFC195E Operating Guide
8. Options
61
8 Options
Multi - Units
8.1 Operating additional
units
units
Additional handsets: Additional handsets are
available for purchase (page 11). Up to 6
handsets can be registered to a single base unit.
Using additional handsets allows you to have an
intercom call while simultaneously conducting a
call to an outside line.
available for purchase (page 11). Up to 6
handsets can be registered to a single base unit.
Using additional handsets allows you to have an
intercom call while simultaneously conducting a
call to an outside line.
L
Additional handsets have answering device
controls printed on their cases, however,
remote operation of the base unit’s
answering device is not possible.
controls printed on their cases, however,
remote operation of the base unit’s
answering device is not possible.
Additional base units: You can register and
operate your handset with up to 4 base units.
Each base unit forms 1 radio cell. If the individual
base units are linked to the same telephone line
then you can extend the operating range of the
system by positioning the base units so that the
two radio cells overlap. If the handset is set to
“AUTO” in base unit selection (page 62), then in
standby mode the handset will automatically
swap to the second base if the range on the first
base is exceeded. It is not possible to transfer
calls between base units (only between
handsets linked to the same base unit).
operate your handset with up to 4 base units.
Each base unit forms 1 radio cell. If the individual
base units are linked to the same telephone line
then you can extend the operating range of the
system by positioning the base units so that the
two radio cells overlap. If the handset is set to
“AUTO” in base unit selection (page 62), then in
standby mode the handset will automatically
swap to the second base if the range on the first
base is exceeded. It is not possible to transfer
calls between base units (only between
handsets linked to the same base unit).
Example: Additional handsets registered to 2
base units.
base units.
Note:
L
Calls are disconnected when the handset
moves from one radio cell to another.
moves from one radio cell to another.
8.2 Registering a handset
to a base unit
to a base unit
The handset supplied with the base unit is
already registered. If an optional handset is
purchased, it must be registered.
already registered. If an optional handset is
purchased, it must be registered.
L
Keep the front cover page open for button
locations.
locations.
Important:
L
After pressing {LOCATOR/HOLD} in step
8, the rest of the procedures must be
completed within 1 minute.
8, the rest of the procedures must be
completed within 1 minute.
L
Charge the optional handset batteries for
7 hours before initial use.
7 hours before initial use.
To exit programming, press {ih} any time.
1
Press {j}.
2
Press {e} or {v} repeatedly to display
“SETTING HS”.
“SETTING HS”.
3
Press {>}.
4
Press {e} or {v} repeatedly to display
“REGISTRATION”.
“REGISTRATION”.
5
Press {>}.
6
Press {e} or {v} repeatedly to display
“REGISTER HS”.
“REGISTER HS”.
7
Press {>}.
8
Press and hold {LOCATOR/HOLD} on the
base unit until the registration tone sounds.
base unit until the registration tone sounds.
L
It may take up to about 10 seconds until
the registration tone sounds.
the registration tone sounds.
L
“REGISTRATION” will be displayed on
the base unit.
the base unit.
L
If all registered handsets start ringing
(paging), press {LOCATOR/HOLD} to
stop paging then start over again.
(paging), press {LOCATOR/HOLD} to
stop paging then start over again.
9
Using the handset, press {e} or {v}
repeatedly to select the desired base unit
number available to register the handset,
and press {>}.
repeatedly to select the desired base unit
number available to register the handset,
and press {>}.
10
After “BS PIN” is displayed, enter the 4-digit
base unit PIN, using the handset dial keypad.
base unit PIN, using the handset dial keypad.
L
The default PIN is “0000”.
11
Press {>} or {j}.
L
When a handset is registered
successfully, a confirmation tone will
sound and w will light.
successfully, a confirmation tone will
sound and w will light.
8.2.1 Cancelling a handset
Each handset can cancel itself or another
handset.
handset.
1
Press {j}.
2
Press {e} or {v} repeatedly to display
“SETTING BS”.
“SETTING BS”.
3
Press {>}.
L
“INPUT CODE” will be displayed.
Radio cell
1
2
3
5
4
chapter8 Page 61 Thursday, March 6, 2003 1:54 PM