Panasonic KXTGF345 Operating Guide
3
Enter the desired hour and minute you
wish to start this feature.
wish to start this feature.
4
*: Select “AM” or “PM”. a MOKN
5
Enter the desired hour and minute you
wish to end this feature.
wish to end this feature.
6
*: Select “AM” or “PM”.
7
MSAVEN a MOFFN
Base unit
1
MMENUN#238
2
MbN: Select the desired setting. a
MSAVEN
R If you select “Off”, press MEXITN to
MSAVEN
R If you select “Off”, press MEXITN to
exit.
3
Enter the desired hour and minute you
wish to start this feature.
wish to start this feature.
4
MAM/PMN: Select “AM” or “PM”. a MOKN
5
Enter the desired hour and minute you
wish to end this feature.
wish to end this feature.
6
MAM/PMN: Select “AM” or “PM”.
7
MSAVEN a MEXITN
Changing the start and end time
Handset / Base unit
1
MMENUN#237
2
Selecting groups to bypass silent
mode
mode
Handset / Base unit
1
MMENUN#241
2
MbN: Select your desired groups. a
MSELECTN
R “
MSELECTN
R “
” is displayed next to the selected
group numbers.
R To cancel the selected group:
MbN: Select the group. a Press
MSELECTN again. “
MSELECTN again. “
” disappears.
3
MSAVEN
4
Proceed with the operation for your unit.
Handset: MOFFN
Base unit: MEXITN
Handset: MOFFN
Base unit: MEXITN
Baby monitor
This feature allows you to listen in on a room
where another handset is located, allowing
you to easily monitor from different areas of
the house or place. The monitored handset
(placed in a baby’s room, for example) will
automatically call the monitoring handset,
base unit, or the phone number stored when it
detects sound.
Important:
R You should perform a test run of the baby
where another handset is located, allowing
you to easily monitor from different areas of
the house or place. The monitored handset
(placed in a baby’s room, for example) will
automatically call the monitoring handset,
base unit, or the phone number stored when it
detects sound.
Important:
R You should perform a test run of the baby
monitor procedure to ensure that the baby
monitor feature is set correctly. For
example, test its sensitivity. Check the
connection if you are diverting the baby
monitor to an outside line.
monitor feature is set correctly. For
example, test its sensitivity. Check the
connection if you are diverting the baby
monitor to an outside line.
R This feature should not be used as a
substitute for a medical or caregiver’s
supervision. It is the caregiver’s
responsibility to stay close enough to
handle any eventuality.
supervision. It is the caregiver’s
responsibility to stay close enough to
handle any eventuality.
Note:
R If the unit is connected to a PBX system,
R If the unit is connected to a PBX system,
you cannot set the baby monitor.
R During the monitoring mode, battery
consumption is faster than usual. We
recommend leaving the monitored handset
on the base unit or charger.
recommend leaving the monitored handset
on the base unit or charger.
R The monitored handset never rings while it
is being monitored. If the base unit is
placed near the monitored handset, we
recommend turning off the base unit ringer
volume (page 33).
placed near the monitored handset, we
recommend turning off the base unit ringer
volume (page 33).
Setting the baby monitor
Perform the setting operation with the handset
to be monitored (for example, the handset
placed in a baby’s room).
to be monitored (for example, the handset
placed in a baby’s room).
To monitor with a unit
The internal baby monitor feature is available:
– between handsets
– between handsets
36
For assistance, please visit http://shop.panasonic.com/support
Programming
TGF34xUS(en)_0221_ver102.pdf 36
2017/02/21 16:31:19