Panasonic KXPRS120E Operating Guide
Important:
R Make sure the unit’s date and time setting
R Make sure the unit’s date and time setting
is correct (page 13).
R If you have set the alarm, the alarm sounds
even if the night mode is turned on.
Turning night mode on/off
1
MMenuN (right soft key) #238
2
MbN: Select the desired setting. a MOKN
R If you select “Off”, press M
R If you select “Off”, press M
N to
exit.
3
Enter the desired hour and minute you
wish to start this feature. a MOKN
wish to start this feature. a MOKN
4
Enter the desired hour and minute you
wish to end this feature. a MOKN a
M
wish to end this feature. a MOKN a
M
N
Changing the start and end time
1
MMenuN (right soft key) #237
2
Setting the ring delay
This setting allows the handset to ring during
night mode if the caller waits long enough.
After the selected amount of time passes, the
handset rings. If you select “No Ringing”,
the handset never rings during night mode.
night mode if the caller waits long enough.
After the selected amount of time passes, the
handset rings. If you select “No Ringing”,
the handset never rings during night mode.
1
MMenuN (right soft key) #239
2
MbN: Select the desired setting. a MOKN
a M
a M
N
Note:
R When the answering system answers the
R When the answering system answers the
call, this feature does not work.
Selecting categories to bypass night
mode
mode
1
MMenuN (right soft key) #241
2
Select your desired categories by
pressing 1 to 9.
R “ ” is displayed next to the selected
pressing 1 to 9.
R “ ” is displayed next to the selected
category numbers.
R To cancel a selected category, press
the same dial key again. “ ”
disappears.
disappears.
3
MOKN a M
N
Nuisance call block
This feature blocks calls from unwanted
callers (Caller ID subscribers only). The
following items are available when storing
phone numbers in the call block list (100 max.).
– “Single Number”: The unit blocks calls
callers (Caller ID subscribers only). The
following items are available when storing
phone numbers in the call block list (100 max.).
– “Single Number”: The unit blocks calls
from specific phone numbers.
– “Range of Numbers”: The unit blocks
calls that begin with a number stored in the
call block list, such as a toll-free phone
number prefix or certain area codes.
call block list, such as a toll-free phone
number prefix or certain area codes.
You can also set the unit to block calls that
have no phone number.
When a call is received, the unit does not ring
while the caller is being identified. If the
caller’s phone number matches an entry in the
call block list, the unit emits no sound to the
caller, and disconnects the call.
Important:
R Blocked calls are logged in the caller list.
have no phone number.
When a call is received, the unit does not ring
while the caller is being identified. If the
caller’s phone number matches an entry in the
call block list, the unit emits no sound to the
caller, and disconnects the call.
Important:
R Blocked calls are logged in the caller list.
Storing unwanted callers
Storing a single phone number
Important:
R You must include the area code when
R You must include the area code when
storing phone numbers in the call block list.
n
From the caller list:
1
M N
2
MbN: Select the entry to be barred. a
MDetailN a MMenuN
MDetailN a MMenuN
3
MbN: “Save CID” a MOKN
4
MbN: “Nuisance Call Block” a MOKN
5
MbN: “Yes” a MOKN a M
N
n
By entering phone numbers:
1
MMenuN (right soft key) #217
2
MbN: “Single Number” a MOKN
3
MMenuN a MbN: “Add” a MOKN
28
Helpline Tel. No.: U.K. 0344 844 3899 Ireland 01289 8333
Programming
PRS120E(en)_0415_ver.210.pdf 28
2015/04/15 10:29:03