Panasonic KXTG9150EX Operating Guide
Multi-unit Operation
54
Operating additional units
Additional handsets
Up to 6 handsets can be registered to a
single base unit.
Important:
single base unit.
Important:
L
The additional handset model
recommended for use with this unit is
noted on page 4. If other model handset is
used, certain operations (handset
settings, base unit settings, etc.) may not
be available.
recommended for use with this unit is
noted on page 4. If other model handset is
used, certain operations (handset
settings, base unit settings, etc.) may not
be available.
L
Additional handsets will give you the
freedom to, for example, have an intercom
call with another handset while a third
handset is on an outside call.
freedom to, for example, have an intercom
call with another handset while a third
handset is on an outside call.
Additional base units
Handsets can be registered to up to 4 base
units, allowing you to add additional base
units and extend the area in which your
handset(s) can be used. If a handset moves
out of range of its base unit when “Auto” is
selected on base unit selection (page 55), it
will look for another base unit to make or
receive calls. A base unit and the handsets it
communicates with is called a “radio cell”.
Note:
units, allowing you to add additional base
units and extend the area in which your
handset(s) can be used. If a handset moves
out of range of its base unit when “Auto” is
selected on base unit selection (page 55), it
will look for another base unit to make or
receive calls. A base unit and the handsets it
communicates with is called a “radio cell”.
Note:
L
Calls will be disconnected when the
handset moves from one radio cell to
another.
handset moves from one radio cell to
another.
Registering a handset to a
base unit
base unit
The included handset and base unit are
preregistered. If for some reason the
handset is not registered to the base unit (for
example, w flashes even when the handset
is near the base unit), register the handset
manually (page 54).
preregistered. If for some reason the
handset is not registered to the base unit (for
example, w flashes even when the handset
is near the base unit), register the handset
manually (page 54).
To register an additional handset to a
base unit (easy registration)
After purchasing an additional handset,
register it to the base unit. Ensure that the
additional handset is switched on. If it is not
on, press and hold {ih} for few seconds
to turn the handset on.
base unit (easy registration)
After purchasing an additional handset,
register it to the base unit. Ensure that the
additional handset is switched on. If it is not
on, press and hold {ih} for few seconds
to turn the handset on.
1
Lift the additional handset and press
{ih}
{ih}
to put the handset in standby
mode.
2
Press and hold {x} on the base unit for
about 3 seconds, until the registration
tone sounds.
about 3 seconds, until the registration
tone sounds.
3
Place the additional handset on the
base unit. The registration tone
continues to sound. With the handset
still on the base unit, wait until a
confirmation tone sounds and w stops
flashing.
base unit. The registration tone
continues to sound. With the handset
still on the base unit, wait until a
confirmation tone sounds and w stops
flashing.
Note:
L
If an error tone sounds, or if w is still
flashing, register the handset manually
(manual registration; page 54).
flashing, register the handset manually
(manual registration; page 54).
L
L
Charge the batteries of your additional
handset for about 7 hours before initial
use.
handset for about 7 hours before initial
use.
L
This registration method cannot be used
for handsets that have already been
registered to a base unit. Register the
handset manually (manual registration;
page 54).
for handsets that have already been
registered to a base unit. Register the
handset manually (manual registration;
page 54).
To register a handset to an additional
base unit (manual registration)
You can register a handset to a base unit
manually using the following method.
base unit (manual registration)
You can register a handset to a base unit
manually using the following method.
1
J
(centre of joystick) i m i L
2
“Registration” i L
3
“Register H.set” i L
4
Select a base unit number. i L
TG9120_40_50EX(e).book Page 54 Monday, August 7, 2006 3:52 PM