Panasonic KXTGL463 Operating Guide
2
MbN: Select the desired setting. a
MSAVEN
R If you select “Off”, press MOFFN to
MSAVEN
R If you select “Off”, press MOFFN to
exit.
3
Enter the desired hour and minute you
wish to start this feature.
wish to start this feature.
4
*: Select “AM” or “PM”. a MOKN
5
Enter the desired hour and minute you
wish to end this feature.
wish to end this feature.
6
*: Select “AM” or “PM”.
7
MSAVEN a MOFFN
Changing the start and end time
1
MMENUN#237
2
Selecting groups to bypass silent
mode
mode
1
MMENUN#241
2
MbN: Select the desired groups. a
MSELECTN
R “
MSELECTN
R “
” is displayed next to the selected
group numbers.
R To cancel the selected group:
MbN: Select the group. a Press
MSELECTN again. “
MSELECTN again. “
” disappears.
3
MSAVEN a MOFFN
Baby monitor
This feature allows you to listen in on a room
where another handset is located, allowing
you to easily monitor from different areas of
the house or even while away from home. The
monitored handset (placed in a baby’s room,
for example) will automatically call the
monitoring handset or the phone number
stored when it detects sound.
Important:
R Before using this feature, we recommend
where another handset is located, allowing
you to easily monitor from different areas of
the house or even while away from home. The
monitored handset (placed in a baby’s room,
for example) will automatically call the
monitoring handset or the phone number
stored when it detects sound.
Important:
R Before using this feature, we recommend
that you test this feature and adjust the
baby monitor sensitivity as needed,
baby monitor sensitivity as needed,
especially if you plan to monitor from
outside.
outside.
R This feature should not be used as a
substitute for a medical or caregiver’s
supervision. It is the caregiver’s
responsibility to stay close enough to
handle any eventuality.
supervision. It is the caregiver’s
responsibility to stay close enough to
handle any eventuality.
Note:
R If the unit is connected to a PBX system,
R If the unit is connected to a PBX system,
you cannot set the baby monitor.
R During the monitoring mode, battery
consumption is faster than usual. We
recommend leaving the monitored handset
on the base unit or charger.
recommend leaving the monitored handset
on the base unit or charger.
R The monitored handset never rings while it
is being monitored. If the base unit is
placed near the monitored handset, we
recommend turning off the base unit ringer
volume (page 35, 37).
placed near the monitored handset, we
recommend turning off the base unit ringer
volume (page 35, 37).
Setting the baby monitor
Perform the setting operation with the handset
to be monitored (for example, the handset
placed in a baby’s room).
to be monitored (for example, the handset
placed in a baby’s room).
To monitor with a unit
The internal baby monitor feature is available
between handsets.
between handsets.
1
MMENUN#268
2
MbN: “On” a MSELECTN
3
MbN: Select the desired unit’s number to
monitor with. a MSAVEN
R “Baby monitor” will be displayed.
R The registered unit’s name/number is
monitor with. a MSAVEN
R “Baby monitor” will be displayed.
R The registered unit’s name/number is
displayed.
Note:
R When this feature is on, another handset
R When this feature is on, another handset
can hear the monitored handset by making
an intercom call.
an intercom call.
To monitor from outside
If you enable this feature, the unit will call a
pre-programmed phone number when the
handset detects sound. After you answer the
call, you can listen in on the room where the
handset is located.
This feature is only available for landline.
pre-programmed phone number when the
handset detects sound. After you answer the
call, you can listen in on the room where the
handset is located.
This feature is only available for landline.
42
For assistance, please visit http://shop.panasonic.com/support
Programming
TGL46x(en)_0126_ver101.pdf 42
2016/01/26 17:25:18