Alpine X009-GM2 In-Dash Restyle System Owner's Manual
51
-EN
Adjusting the Frequency
Touch [
] or [
] of “Freq.” to adjust the frequency of the
selected band.
Adjustable frequency bands: 20 Hz to 20 kHz (in 1/3 octave steps)
Adjusting the Level
Touch [
] or [
] of “Level” to adjust the level of selected
band.
Setting contents: -7 to +7 (Initial setting: 0)
Setting the Bandwidth
Touch [
] or [
] of “Q Adjust” to select the bandwidth.
Setting contents: Wide (Initial setting) / Medium / Narrow
2
To adjust another band, repeat step 1, and adjust all
bands.
bands.
3
To store the adjusted setting value, touch and hold
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
• BAND2 and BAND8 are the same as the Bass and Treble controls.
Their Level adjustment can also be controlled by pressing and
holding
holding
/ AUDIO and selecting Bass Level or Treble Level. Refer
• Settings exceeding the frequency of adjacent bands are not available.
• While adjusting the Parametric EQ, you should consider the
• While adjusting the Parametric EQ, you should consider the
frequency response of the connected speakers.
• When the parametric EQ is adjusted, the Equalizer Presets are
overridden.
• When Equalizer Presets is set, the linked Parametric EQ settings are
also changed. We recommend storing Parametric EQ settings in a
Preset in advance.
Preset in advance.
• Touch [Flat] to initialize all values.
• The Parametric EQ setting can be configured when Defeat is “Off”.
• The Parametric EQ setting can be configured when Defeat is “Off”.
Calling the Parametric EQ adjusted value
Calling the pre-set Parametric EQ adjusted value.
Touch [Preset1], [Preset2], or [Preset3] on the
Parametric EQ screen.
Parametric EQ screen.
The setting stored in the Preset will be recalled.
Adjusting the Time Correction (Time
Correction)
Correction)
[Time Correction] is selected on the Sound setup menu in step 3. Refer
to “Sound Setup Operation” (page 48).
Before performing the following procedures, refer to “About Time
Correction” (page 53).
to “Sound Setup Operation” (page 48).
Before performing the following procedures, refer to “About Time
Correction” (page 53).
Setting item: Time Correction
1
Touch [cm], [inch] or [ms] to select mode for
making adjustments.
making adjustments.
Each time you touch, the onscreen button and correction
mode changes.
mode changes.
cm/inch: Adjust listening position and distance from each
speaker.
ms: Adjust time.
speaker.
ms: Adjust time.
2
Touch [
] or [
] for each speaker to adjust the
time or distance.
0.0 msec to 9.9 msec (0.1 msec/step)
0.0 cm (0.0 inch) to 336.6 cm (132.7 inch) (3.4 cm/step)
All speaker setting values are adjustable in the range of 15 ms
or 510 cm.
0.0 cm (0.0 inch) to 336.6 cm (132.7 inch) (3.4 cm/step)
All speaker setting values are adjustable in the range of 15 ms
or 510 cm.
3
To store the adjusted setting value, touch and hold
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
• Touch [Flat] to set all values to 0.0.
• If the Rear Speaker setting is “Off”, the Rear Speaker setting cannot
• If the Rear Speaker setting is “Off”, the Rear Speaker setting cannot
be edited (refer to page 49).
• If the Subwoofer setting is “Off”, the Subwoofer setting cannot be
edited (refer to page 49).
Calling the Time Correction Value
Calling the pre-set time correction value.
Touch [Preset1], [Preset2], or [Preset3] on the time
correction screen.
correction screen.
The setting stored in the Preset will be recalled.
Band1: 20 Hz~100 Hz (63 Hz)
Band2: 63 Hz~315 Hz (125 Hz)
Band3: 125 Hz~500 Hz (250 Hz)
Band4: 250 Hz~1 kHz (500 Hz)
Band5: 500 Hz~2 kHz (1 kHz)
Band6: 1 kHz~4 kHz (2 kHz)
Band7: 2 kHz~7.2 kHz (4 kHz)
Band8: 5.8 kHz~12 kHz (8 kHz)
Band9: 9 kHz~20 kHz (16 kHz)
Correction mode