Alpine X009-GM2 In-Dash Restyle System Owner's Manual
52
-EN
Adjusting the Crossover Settings
(X-Over)
(X-Over)
[X-Over] is selected on the Sound setup menu in step 3. Refer to
“Sound Setup Operation” (page 48).
Before performing the following procedures, refer to “About the
Crossover” (page 54).
“Sound Setup Operation” (page 48).
Before performing the following procedures, refer to “About the
Crossover” (page 54).
Setting item: X-Over
1
Touch [Channel] to select the channel.
Each time you touch, the channel switches.
• The channel being adjusted is displayed in red.
2
Adjust the crossover to your preference.
Selecting the Cut-Off Frequency
Touch [
] or [
] of “Freq.”, and then select the cut-off
frequency.
Setting contents: 20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) /
100 / 125 / 160 / 200 Hz
Adjusting the Slope
Touch [
] or [
] of “Slope”, and then adjust the HPF or LPF
slope.
Setting contents: 0 (Initial setting) / 6 / 12 / 18 / 24 dB/oct.
Adjusting the Level
Touch [
] or [
] of “Level”, and then adjust the HPF or LPF
level.
Setting contents: -12 to 0 dB (Initial setting: 0)
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
channels.
4
To store the adjusted setting value, touch and hold
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
• Touch [Flat] to initialize all values.
• If the Rear Speaker setting is “Off”, the Rear Speaker setting cannot
• If the Rear Speaker setting is “Off”, the Rear Speaker setting cannot
be edited (refer to page 49).
• If the Subwoofer setting is “Off”, the Subwoofer setting cannot be
edited (refer to page 49).
• While adjusting the X-Over you should consider the frequency
response of the connected speakers.
Calling the X-Over adjusted value
Calling the pre-set X-Over adjusted value.
Touch [Preset1], [Preset2], or [Preset3] on the
X-Over screen.
X-Over screen.
The setting stored in the Preset will be recalled.
Setting Defeat
[Defeat] is selected on the Sound setup menu in step 3. Refer to “Sound
Setup Operation” (page 48).
If Defeat is “On”, MX, Equalizer Presets, Car Specific Sound Setup and
Parametric EQ functions are turned OFF. This disables any settings
made for these functions.
Setup Operation” (page 48).
If Defeat is “On”, MX, Equalizer Presets, Car Specific Sound Setup and
Parametric EQ functions are turned OFF. This disables any settings
made for these functions.
Setting item: Defeat
Setting contents: Off (Initial setting) / On
Setting contents: Off (Initial setting) / On
Volume Setting
[Volume] is selected on the Sound setup menu in step 3. Refer to
“Sound Setup Operation” (page 48).
You can change the volume of the sound heard when a button is
touched.
“Sound Setup Operation” (page 48).
You can change the volume of the sound heard when a button is
touched.
Setting item: Key Sound Feedback
Setting contents: 0 to 7 (Initial setting: 4)
Setting contents: 0 to 7 (Initial setting: 4)
Setting the Volume for Each Source
[Source Volume Setup] is selected on the Sound setup menu in step 3.
Refer to “Sound Setup Operation” (page 48).
The volume level for each application can be adjusted.
Refer to “Sound Setup Operation” (page 48).
The volume level for each application can be adjusted.
Setting item: Radio / SiriusXM / DVD / CD / Compressed Media /
iPod Music / iPod Video / HDMI / Pandora / AUX /
AUX3 / Bluetooth Audio / iDataLink
AUX3 / Bluetooth Audio / iDataLink
Setting contents: -14 to +14 (Initial setting: 0)
• Settable source differ depending on the connected device and
settings.
Front HPF
Rear HPF
Subw. LPF