Q-Logic Q-Forms Kick Panel Enclosures Owner's Manual
Dodge/Plymouth Neon 1994-2000
QL-K3006
Remove Original Kick Panel
• Remove threshold plate by prying upward along bottom edge.
• Pull kick panel away from bulkhead to release mounting clips.
• Remove the kick panels from the vehicle
• Pull kick panel away from bulkhead to release mounting clips.
• Remove the kick panels from the vehicle
NOTE: Always check the fit of the Q-Forms into the vehicle before any cutting or modifications are done.
Preparing the Q-Forms for Speaker Installation
• Cut the speaker holes into the Q-Forms before installing them into the vehicle.
• Install the speakers into the Q-Forms after they have been installed into the vehicle.
• Install speaker wiring and crossover network as per manufacturer’s instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of speaker mounting surface.
A die grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and into mounting surface.
• Install the speakers into the Q-Forms after they have been installed into the vehicle.
• Install speaker wiring and crossover network as per manufacturer’s instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of speaker mounting surface.
A die grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and into mounting surface.
Be careful to center speakers in mounting surface to allow clearance for grill shell.
• Install tweeters as per manufacturer’s instructions.
Install New Q-Forms Kick Panels (Always predrill all mounting screw locations)
Driver's Side
Driver's Side
• Slide the Q-Forms kick panels into place.
• While securely holding panel into place, mark and pre-drill the two mounting locations. One behind the hood
• While securely holding panel into place, mark and pre-drill the two mounting locations. One behind the hood
release lever and one at the upper rear of the Q-Form.
• Secure the front location behind the hood release's resting position with supplied 1" Truss head screw.
• Secure the upper rear location with supplied 1-1/2" white nylon spacer and 2" screw.
• Reinstall factory threshold plate.
• Install speakers. Place the rubber "U" channel on the edge of the painted grill and press into the grill recess.
• Secure the upper rear location with supplied 1-1/2" white nylon spacer and 2" screw.
• Reinstall factory threshold plate.
• Install speakers. Place the rubber "U" channel on the edge of the painted grill and press into the grill recess.
Passenger's Side
• Slide the Q-Form kick panel into place.
• While securely holding panel in place, mark and pre-drill two mounting locations, one on upper front edge of
• While securely holding panel in place, mark and pre-drill two mounting locations, one on upper front edge of
the panel and one on the bottom, below the speaker locations, of the Q-Forms panel.
• Secure the upper front location with the supplied 1" screw.
• Secure the lower edge, below the speaker locations, with the supplied 2" screw.
• Reinstall factory threshold plate.
• Install speakers. Place the rubber "U" channel on the edge of the painted grill and
press into the grill recess.
QL-K3006 Included Hardware:
(1) 1" screw
• Secure the lower edge, below the speaker locations, with the supplied 2" screw.
• Reinstall factory threshold plate.
• Install speakers. Place the rubber "U" channel on the edge of the painted grill and
press into the grill recess.
QL-K3006 Included Hardware:
(1) 1" screw
(1) 1" truss head screw
(2) 2" screws
(1) 1-1/2" white nylon spacer
(2) Q-grills
(2) 6" x 8" poly-fil pieces
(1) 40" piece "U" channel
Estimated Installation Time: 1.5 Hrs.
7/18/00