Thunder Tiger Corp. TT-FHM2P4G-A16 User Manual
Battery cover
Transmitter batteries replacement/installation:
1)
2)
1)
2)
3)
4)
4)
Slide the battery cover in the direction as shown to remove the cover.
Install 8pcs alkaline or rechargeable “AA” size cells into the battery
holder connected to the transmitter.
Slide on the battery cover and make sure it is closed securely.
Turn the power on to check. If the Power Indicator LED fails to light,
check the batteries for insufficient contact or incorrect battery polarity.
Install 8pcs alkaline or rechargeable “AA” size cells into the battery
holder connected to the transmitter.
Slide on the battery cover and make sure it is closed securely.
Turn the power on to check. If the Power Indicator LED fails to light,
check the batteries for insufficient contact or incorrect battery polarity.
Installation
Functions
NOTE:
a)
b)
a)
b)
c)
d)
Use only same brand, fresh, alkaline cells.
Ensure all contacts in the battery holder are clean by using a pencil eraser
to gently remove any corrosion or dirt that may accumulate. It is
recommended to do this each time you install fresh cells into your
transmitter.
If using rechargeable 9.6V battery-pack. Remove the battery holder by
pulling out the connector from the transmitter. Then plug-in the
battery-pack connector to the transmitter.
When rechargeable batteries are installed in the transmitter, these can be
charged through the external charging jack located on the transmitter.
Ensure all contacts in the battery holder are clean by using a pencil eraser
to gently remove any corrosion or dirt that may accumulate. It is
recommended to do this each time you install fresh cells into your
transmitter.
If using rechargeable 9.6V battery-pack. Remove the battery holder by
pulling out the connector from the transmitter. Then plug-in the
battery-pack connector to the transmitter.
When rechargeable batteries are installed in the transmitter, these can be
charged through the external charging jack located on the transmitter.
CAUTION:
a)
b)
a)
b)
c)
d)
Do not attempt to charge alkaline batteries, they may explode!!
When charging rechargeable batteries, turn off the power switch before
charging. The charger plug must be of the correct type (“+” inside and
“-“ outside, type TAMIYA N-3U or equivalent). Incorrect charger plug
type may provoke an explosion, causing personal injuries and
damages.
Always ensure batteries are loaded in the correct polarity. If the
batteries are loaded incorrectly, the transmitter may be damaged.
When the transmitter is not used for any short / long period of time,
always remove the batteries from the transmitter.
When charging rechargeable batteries, turn off the power switch before
charging. The charger plug must be of the correct type (“+” inside and
“-“ outside, type TAMIYA N-3U or equivalent). Incorrect charger plug
type may provoke an explosion, causing personal injuries and
damages.
Always ensure batteries are loaded in the correct polarity. If the
batteries are loaded incorrectly, the transmitter may be damaged.
When the transmitter is not used for any short / long period of time,
always remove the batteries from the transmitter.
The Innovator TS6
+
transmitter was specifically-designed to operate with
the Innovator R/C helicopter. Basic functions for this transmitter are
indicated below.
indicated below.
1.Power On
1.1 Turn On/Off
1.1 Turn On/Off
After installing the transmitter batteries,
turn on the transmitter power by
pressing the “PWR” switch button
located on the front of the transmitter.
Release upon hearing a short “Beep”
tone confirming power is “On”. The LED
indicator will also turn red. To turn power
off, press the “PWR” button and release
upon hearing a long ‘Beep” tone,
confirming power is “Off’. The LED
indicator will also turn off.
turn on the transmitter power by
pressing the “PWR” switch button
located on the front of the transmitter.
Release upon hearing a short “Beep”
tone confirming power is “On”. The LED
indicator will also turn red. To turn power
off, press the “PWR” button and release
upon hearing a long ‘Beep” tone,
confirming power is “Off’. The LED
indicator will also turn off.
Battery cell (x8)
While pressing
this part
this part
3