Thunder Tiger Corp. TT-FHM2P4G-A16 User Manual
NOTE:
Binding process may take 3~10 seconds to execute. If binding fails, the LED
light on the receiver will turn red. Please turn off power and repeat the above
steps from a) ~ e).
Binding process may take 3~10 seconds to execute. If binding fails, the LED
light on the receiver will turn red. Please turn off power and repeat the above
steps from a) ~ e).
5
a)
b)
c)
d)
e)
Press and hold “Binding SW” button located on the right lower side
of the transmitter.
Simultaneously, turn on the power by pressing the ‘PWR” button
until a short ‘Bi” tone confirms power is on.
Release “Binding SW”. The binding LED will blink rapidly, indicating
the transmitter is binding.
To perform binding process from the Innovator R/C helicopter,
press and hold the push button on the Innovator helicopter, slide in
the battery pack to turn on the helicopter/receiver power. Binding
process will then start automatically.
Successful binding is confirmed by the binding LED changing from
a rapid blink to a slow flash on the transmitter. The LED will turn
green on the receiver. Upon confirmation, turn off power on the
helicopter and transmitter and launch normal start-up procedures.
of the transmitter.
Simultaneously, turn on the power by pressing the ‘PWR” button
until a short ‘Bi” tone confirms power is on.
Release “Binding SW”. The binding LED will blink rapidly, indicating
the transmitter is binding.
To perform binding process from the Innovator R/C helicopter,
press and hold the push button on the Innovator helicopter, slide in
the battery pack to turn on the helicopter/receiver power. Binding
process will then start automatically.
Successful binding is confirmed by the binding LED changing from
a rapid blink to a slow flash on the transmitter. The LED will turn
green on the receiver. Upon confirmation, turn off power on the
helicopter and transmitter and launch normal start-up procedures.
7.Range-Check
Note:
Never push the “Binding SW” button during flight. Flying under weak signal
strength will result in signal loss and model crash.
Never push the “Binding SW” button during flight. Flying under weak signal
strength will result in signal loss and model crash.
6.Binding Process
A binding feature is included in the Innovator 2.4 GHz
spread spectrum system to ensure the transmitter and
receiver bind properly and prevent interference from
other controllers. With the Super Combo package, full
binding procedure has been completed at the factory
prior to shipping. To manually bind Tx/Rx, please
proceed as per the following steps:
spread spectrum system to ensure the transmitter and
receiver bind properly and prevent interference from
other controllers. With the Super Combo package, full
binding procedure has been completed at the factory
prior to shipping. To manually bind Tx/Rx, please
proceed as per the following steps:
A built-in range-check function on the transmitter reduces signal
strength for pre-flight. When this function is activated, signal strength is
weak. Use the weak signal strength for pre-flight range-check to
confirm the operation of the radio control system is normal. It is
recommended to perform a complete range-check procedure before
every flight.
step of “Range-Check” procedure:
strength for pre-flight. When this function is activated, signal strength is
weak. Use the weak signal strength for pre-flight range-check to
confirm the operation of the radio control system is normal. It is
recommended to perform a complete range-check procedure before
every flight.
step of “Range-Check” procedure:
a)
b)
c)
d)
e)
f)
Turn both transmitter and helicopter power on and ensure the
system is functioning properly.
Take the transmitter to a distance of about 20~30m from the model
/ helicopter.
Press and hold the “Binding SW” button. Signal strength is now
weak. The transmitter buzzer will signal with a short “Bi-Bi-Bi”
warning tone and green LED blink. Please do not release “Binding
SW” button at this stage.
While still holding “”Binding SW” button, operate both left and right
sticks to drive movements on the helicopter’s control linkages.
Confirm that all movements are accurate and signal is
interference-free.
Release “Binding SW” button. Signal reverses back to full strength
and warning tone stops.
Helicopter is ready to fly.
system is functioning properly.
Take the transmitter to a distance of about 20~30m from the model
/ helicopter.
Press and hold the “Binding SW” button. Signal strength is now
weak. The transmitter buzzer will signal with a short “Bi-Bi-Bi”
warning tone and green LED blink. Please do not release “Binding
SW” button at this stage.
While still holding “”Binding SW” button, operate both left and right
sticks to drive movements on the helicopter’s control linkages.
Confirm that all movements are accurate and signal is
interference-free.
Release “Binding SW” button. Signal reverses back to full strength
and warning tone stops.
Helicopter is ready to fly.
8.Flying the Simulator
Use a suitable interface device to connect the mini USB port (located
on the back of the transmitter) to a personal computer and directly fly
the Innovator on the simulator (simulator software sold separately).
on the back of the transmitter) to a personal computer and directly fly
the Innovator on the simulator (simulator software sold separately).