The Bodine Company FEBNET01 User Manual
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
bodine
®
! IMPORTANT SAFEGUARDS !
WHEN USING ELECTRICAL EQUIPMENT, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
©The Bodine Company, Inc.
236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.bodine.com
70450021
FLUORESCENT EMERGENCY BALLAST NETWORK SYSTEM
Installation Instructions
1. To prevent damage to the FEBnet Node, only use the power supply provided.
2. An unswitched AC power source is required for operation of the FEBnet Node (100-240 VAC, 50-60 Hz).
3. This product is suitable for installation in indoor, dry locations only.
4. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
5. Do not use this product for other than intended use.
6. Servicing should be performed by qualified service personnel.
7. NOTICE: This equipment complies with the FCC RF Exposure Limits. A minimum of 20 centimeters (8 inches)
2. An unswitched AC power source is required for operation of the FEBnet Node (100-240 VAC, 50-60 Hz).
3. This product is suitable for installation in indoor, dry locations only.
4. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
5. Do not use this product for other than intended use.
6. Servicing should be performed by qualified service personnel.
7. NOTICE: This equipment complies with the FCC RF Exposure Limits. A minimum of 20 centimeters (8 inches)
separation between the device and the user and all other persons should be maintained.
FEBnet Node
05/18/05
FCC COMPLIANCE STATEMENT
1.
WARNING:
The antenna used for this device must be installed to provide a separation distance of at least 20cm (8 inches)
from all persons, and must not be co-located or operating in conjunction with any other antenna or transmitter other than
those contained within this device.
those contained within this device.
2.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
operate the equipment.
3.
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or devices
•
Connect the equipment to an outlet other than the receiver’s
•
Consult a dealer or an experienced radio/TV technician for assistance
SAVE THESE INSTRUCTIONS
OVERVIEW
The FEBnet Node is a device intended for use with the FEBnet system. When wired into the network, this device will convert
RS-485 information from the FEBnet Hub to wireless information for a FEBnet emergency ballast. Additionally, the FEBnet
Node will convert the wireless information from a FEBnet emergency ballast to RS-485 information suitable for the FEBnet
Hub. The FEBnet Node is powered by 100 to 240 VAC and can be wall-mounted or placed on a shelf or desktop.
RS-485 information from the FEBnet Hub to wireless information for a FEBnet emergency ballast. Additionally, the FEBnet
Node will convert the wireless information from a FEBnet emergency ballast to RS-485 information suitable for the FEBnet
Hub. The FEBnet Node is powered by 100 to 240 VAC and can be wall-mounted or placed on a shelf or desktop.
"OUFOOB
OPUSFNPWBCMF
*OEJDBUFTJGQPXFS
JTDPOOFDUFEUP/PEF
*OEJDBUFTUSBOTNJUUJOH
EBUBUP)VCWJB34
*OEJDBUFTSFDFJWJOH
EBUBGSPN)VCWJB34
*OEJDBUFTUSBOTNJUUJOH
EBUBUP#BMMBTUWJB3'
*OEJDBUFTSFDFJWJOH
EBUBGSPN#BMMBTUWJB3'
341PSUT
1PXFS$POOFDUJPO
6TF*ODMVEFE1PXFS4VQQMZ