Impinj Inc. XARRAY User Manual
Speedway Revolution Installation and Operations Guide Octane 4.11
Revision 4.11 Copyright ©2014, Impinj, Inc.
iii
Caution:
Changes to this product or
modifications not expressly approved by the
party responsible for compliance could void
your authority to operate per FCC Part 15.
party responsible for compliance could void
your authority to operate per FCC Part 15.
Attention:
Les modifications apportées à
ce produit ou modifications pas
expressément approuvés par la partie
responsable de la conformité peuvent
annuler votre droit à utiliser par FCC Part 15.
expressément approuvés par la partie
responsable de la conformité peuvent
annuler votre droit à utiliser par FCC Part 15.
Industry Canada (IC) Compliance
Operation is subject to the following two
conditions:
conditions:
1. This device may not cause
interference.
2. This device must accept any
interference, including interference
that may cause undesired operation
of the device.
that may cause undesired operation
of the device.
listed on page 36 that
have a maximum gain of 6 dB. Antennas not
included in this list or having a gain greater
than 6 dB are strictly prohibited for use with
this device. The required antenna impedance
is 50 ohms. To reduce potential radio
interference to other users, the antenna type
and its gain should be chosen so that the
equivalent isotropically radiated power
(EIRP) is not more than that permitted for
successful communication. The term ―IC‖
before the radio certification number only
signifies that Industry of Canada technical
specifications were met.
included in this list or having a gain greater
than 6 dB are strictly prohibited for use with
this device. The required antenna impedance
is 50 ohms. To reduce potential radio
interference to other users, the antenna type
and its gain should be chosen so that the
equivalent isotropically radiated power
(EIRP) is not more than that permitted for
successful communication. The term ―IC‖
before the radio certification number only
signifies that Industry of Canada technical
specifications were met.
Industrie Canada (IC) Conformité
Son fonctionnement est soumis aux deux
conditions suivantes:
conditions suivantes:
1. Cet appareil ne doit pas
provoquer d'interférences.
2. Cet appareil doit accepter toute
interférence, y compris celles
pouvant causer un mauvais
fonctionnement de l'appareil.
pouvant causer un mauvais
fonctionnement de l'appareil.
Cet appareil a été conçu pour fonctionner
avec l'antenne (s) énumérées à la page 35
qui ont un gain maximum de 6 dB. Antennes
pas inclus dans cette liste ou présentant un
gain supérieur à 6 dB sont strictement
interdits pour utilisation avec cet appareil.
L'impédance d'antenne requise est de 50
ohms. Afin de réduire le risque d'interférence
avec d'autres utilisateurs, le type d'antenne
et son gain doivent être choisis de telle sorte
que la puissance isotrope rayonnée
équivalente (PIRE) ne soit pas supérieure à
celle permise pour une communication
réussie. L‘expression "IC" avant le numéro
de certification radio signifie seulement que
l'industrie des spécifications techniques
Canada ont été respectées.
avec l'antenne (s) énumérées à la page 35
qui ont un gain maximum de 6 dB. Antennes
pas inclus dans cette liste ou présentant un
gain supérieur à 6 dB sont strictement
interdits pour utilisation avec cet appareil.
L'impédance d'antenne requise est de 50
ohms. Afin de réduire le risque d'interférence
avec d'autres utilisateurs, le type d'antenne
et son gain doivent être choisis de telle sorte
que la puissance isotrope rayonnée
équivalente (PIRE) ne soit pas supérieure à
celle permise pour une communication
réussie. L‘expression "IC" avant le numéro
de certification radio signifie seulement que
l'industrie des spécifications techniques
Canada ont été respectées.
CE Marking and European Economic Area (EEA)
RFID devices designed for use throughout the EEA must have a maximum radiated transmit
power of 2W ERP in the frequency range of 865.6–867.6 MHz. For other EEA restrictions on
RFID device use, please refer to the Impinj Declaration of Conformity (DoC) located at
power of 2W ERP in the frequency range of 865.6–867.6 MHz. For other EEA restrictions on
RFID device use, please refer to the Impinj Declaration of Conformity (DoC) located at
Environmental Air Handling Space (EAHS) Applications
This device is suitable for use in Environmental Air Handling Space (EAHS) in accordance
with Section 300-22(c) of the National Electric Code.
with Section 300-22(c) of the National Electric Code.