Riello Sentinel Dual 10000VA CSDLK10TA5 User Manual
Product codes
CSDLK10TA5
www.riello-ups.co.uk
UP
S
49
• Operation guaranteed up to 40°C (the
components are designed for high
temperatures and are thus subject to
less stress at normal temperatures)
temperatures and are thus subject to
less stress at normal temperatures)
• Two built-in IEC output sockets with
thermal protection (5-6- 8-10 kVA)
• Two 10A outpit sockets with Power
Share on the 5-6-8-10 kVA models
that can be turned off when the mains
power supply fails.
that can be turned off when the mains
power supply fails.
Operation selection
Programmed using the software supplied or
manually via the front mimic panel
• On-line double conversion Mode: to
Programmed using the software supplied or
manually via the front mimic panel
• On-line double conversion Mode: to
provide maximum protection.
• ECO Mode:to increase output (up to
98%), operating in line interactive (VI)
mode, powering loads from the mains.
mode, powering loads from the mains.
• Smart Active Mode: the UPS
automatically decides upon the
operating mode (VI or VFI) based on the
quality of the mains power supply.
operating mode (VI or VFI) based on the
quality of the mains power supply.
• Emergency Mode: the UPS can be
selected to function only when mains
power fails (emergency mode only)
power fails (emergency mode only)
• Frequency converter (50 or 60 Hz).
High quality output voltage
• Even with non-linear loads (loads with a
• Even with non-linear loads (loads with a
rest factor of up to 3:1)
• High short circuit current on Bypass
• High overload capacity 150% by
• High overload capacity 150% by
inverter (even with mains failure
• Filtered, stabilised and reliable voltage
(double conversion On-line technology
(VFI compliant with IEC 62040-3)
with filters for the suppression of
atmospheric disturbances.
(VFI compliant with IEC 62040-3)
with filters for the suppression of
atmospheric disturbances.
• Power factor correction: UPS input
power factor, close to 1 and sinewave
current absorption
current absorption
High battery reliability
• Automatic and manual battery test
• Reduced ripple component (detrimental
• Automatic and manual battery test
• Reduced ripple component (detrimental
to the batteries) using the “LRCD” (Low
Ripple Current Discharge) system
Ripple Current Discharge) system
• Batteries are user replaceable without
interruption to the load (Hot Swap)
• Unlimited extendible runtime using
matching Battery Boxes
• High hold-up time and wide input
voltage range. The batteries are not
used during mains power supply
failures of <40 ms or within an input
voltage range of 84-276V.
used during mains power supply
failures of <40 ms or within an input
voltage range of 84-276V.
Emergency Back-up function
This configuration is designed for
emergency systems incljuding lighting,
fire detection/exit systems and alarms.
When the mains power supply fails, the
inverter begins powering the loads with
a progressive start (Soft Start) in order to
prevent overload.
This configuration is designed for
emergency systems incljuding lighting,
fire detection/exit systems and alarms.
When the mains power supply fails, the
inverter begins powering the loads with
a progressive start (Soft Start) in order to
prevent overload.
Battery optimisation
The wide input voltage range and a high
hold-up time minimise battery usage and
increase efficiency and battery life; for
smaller power breaks, energy is drawn from
a group of appropriately-sized capacitors.
The wide input voltage range and a high
hold-up time minimise battery usage and
increase efficiency and battery life; for
smaller power breaks, energy is drawn from
a group of appropriately-sized capacitors.
Power Share (5-10kVA)
Two configurable IEC output sockets,
for runtime optimisation, with the facility
to programme the sockets to switch-off
low priority loads on mains power failure;
alternatively, emergency loads, normally
not powered when the mains is present,
can be activated.
Two configurable IEC output sockets,
for runtime optimisation, with the facility
to programme the sockets to switch-off
low priority loads on mains power failure;
alternatively, emergency loads, normally
not powered when the mains is present,
can be activated.
Low noise output
Using digital PWM control, the speed
of the load dependent fans is adjusted
depending on the temperature of the two
internal heatsinks, to achieve a reduced
noise level of 45dB and help extend their
operating life.
Using digital PWM control, the speed
of the load dependent fans is adjusted
depending on the temperature of the two
internal heatsinks, to achieve a reduced
noise level of 45dB and help extend their
operating life.
Other features
• Output voltage can be selected using
• Output voltage can be selected using
software (220-230-240V)
• Auto-restart when mains power is
restored (programmable via software)
• Bypass on: when the machine is
switched off, it automatically goes into
bypass and battery charge mode
bypass and battery charge mode
• Minimum load switch-off
• Low battery warning
• Start-up delay
• Total microprocessor control
• Automatic bypass without interruption
• Use of IMS modules (Insulated Metallic
• Low battery warning
• Start-up delay
• Total microprocessor control
• Automatic bypass without interruption
• Use of IMS modules (Insulated Metallic
Substrates)
• Statuses, measurements and alarms
available on standard, backlit display.
• UPS digital updating (flash upgradable)
• Input protection through resettable
• Input protection through resettable
thermal switch
• Standard Back-feed protection: to
prevent energy from being fed back to
the network
the network
• Manual switching to bypass.
90°
90°
2. Rotate the mimic panel counter
clockwise and then secure it back
in place
1. Release the mimic panel by
applying pressure to the catch
3. Rotate the UPS 90°
4. Attach the rack supports