Inovonics Wireless Corporation 3B6ETRT2M User Manual
2
TO INSTALL A BATTERY
1. Using a flat screwdriver, open the housing. Insert the screwdriver
about .25" (6mm) at the tab on the top of the unit (Fig. 3). Pry
downward on the handle of the screwdriver until the latch holding
the cover to the housing base releases.
downward on the handle of the screwdriver until the latch holding
the cover to the housing base releases.
2. Install the battery using the polarity (+ and -) markings on the
battery and equipment. Do not use excessive force. If the battery
does not fit, ensure that it matches the polarity markings (Fig. 2).
does not fit, ensure that it matches the polarity markings (Fig. 2).
3. Press the reset button (F) on the device. After resetting the Key
Chain Remote (see Device Registration), replace the cover.
TO CHANGE THE BATTERY
CAUTION: Never use a damaged or worn out battery.
CAUTION: Never use a damaged or worn out battery.
1. Carefully remove the old, discharged battery. Dispose of the
battery according to local regulations.
2. Install new battery using the polarity (+ and -) markings on the
battery and equipment. Do not use excessive force. If the battery
does not fit, ensure that it matches the polarity markings (Fig. 2).
does not fit, ensure that it matches the polarity markings (Fig. 2).
3. Press the reset button (F) on the device to re-register the sensor
and restore programming. After resetting the Key Chain Remote,
replace the cover.
replace the cover.
Device Registration
To activate the remote, it must first be assigned to your DS100 Base
Unit. Refer to the DS100 JobSite Security Portable Alarm System
Instruction Manual for more details on registering a device during the
initial setup.
NOTE: The system must be disarmed prior to any programming
changes.
Unit. Refer to the DS100 JobSite Security Portable Alarm System
Instruction Manual for more details on registering a device during the
initial setup.
NOTE: The system must be disarmed prior to any programming
changes.
1. Press the MAIN MENU button on the keypad of the DS100 Base
Unit.
2. Using the keypad, enter the master code.
3. Use the up and down arrows to scroll through the menu until the
3. Use the up and down arrows to scroll through the menu until the
System Settings menu is displayed. Select OK.
4. Use the up and down arrows to scroll through the menu until the
Wireless Device Maintenance menu is displayed. Select OK.
5. Use the up and down arrows to scroll through the menu until the
Add/Replace Device screen is displayed. Select OK.
6. The next available device number will be displayed. Up to six Key
Chain Remotes can be registered to the system. If there are no
slots available, the screen will display ALL DEVICES IN USE.
When the device number is shown, select OK.
slots available, the screen will display ALL DEVICES IN USE.
When the device number is shown, select OK.
7. Using a flat screwdriver, open the housing. Insert the screwdriver
about .25" (6 mm) at the tab on the top of the unit. Pry upward on
the handle of the screwdriver until the latch holding the cover to
the housing base releases (Figure 3).
the handle of the screwdriver until the latch holding the cover to
the housing base releases (Figure 3).
8. When prompted by the LCD screen to RESET DEVICE, press and
release the reset button (F) located on the control board. The
screen will indicate that the device has been registered.
screen will indicate that the device has been registered.
9. Snap the cover into place.
10. To edit the description of the device, select EDIT.
11. To edit the description, use the keypad to type a description of up
to 8 characters. The character that is being changed will be under-
lined. To move back a character, use the left/down arrow. To move
forward a character, use the right/up arrow. When complete, select
SAVE.
lined. To move back a character, use the left/down arrow. To move
forward a character, use the right/up arrow. When complete, select
SAVE.
IMPORTANT: Write the device description and corresponding
device number on the Sensor Location List included with the
DS100 JobSite Security Portable Alarm System. Keep this sheet
for reference. This information will be needed during the monitoring
service enrollment process. As device changes are made, be sure
to contact D
device number on the Sensor Location List included with the
DS100 JobSite Security Portable Alarm System. Keep this sheet
for reference. This information will be needed during the monitoring
service enrollment process. As device changes are made, be sure
to contact D
E
WALT customer service to make adjustments to the
monitoring service.
12. After registration, test the remote. If programming through the
initial setup, the test function will be included in the setup
sequence. If adding the Key Chain Remote after the alarm system
has been programmed, use the TEST button on the keypad.
sequence. If adding the Key Chain Remote after the alarm system
has been programmed, use the TEST button on the keypad.
Walk Test
To activate the Key Chain Remote Control during a walk test, press
the lock ( ) button on the remote. The Base Unit will indicate that the
test was successful when the device is removed from the list on the
LCD screen.
IMPORTANT: To prevent false alarms, be sure to have a good under-
standing of the range of the system for arming and disarming.
the lock ( ) button on the remote. The Base Unit will indicate that the
test was successful when the device is removed from the list on the
LCD screen.
IMPORTANT: To prevent false alarms, be sure to have a good under-
standing of the range of the system for arming and disarming.
To test the range of the Key Chain Remote, perform the walk test from
any area throughout the job site that may be used as an entry or exit
point.
any area throughout the job site that may be used as an entry or exit
point.
Faults
Faults indicate when there has been a serious issue that needs to be
addressed. This could be a number of things including a low battery
or weak signal.
If a fault is present, the system will chime and the Fault screen will be
displayed. To silence the chime, select SILENCE. To display the fault
and resolve immediately, select DISPLAY. Use the up and down
arrows to scroll through the faults. Resolve the issue with the action
listed in Description of Fault Codes chart.
addressed. This could be a number of things including a low battery
or weak signal.
If a fault is present, the system will chime and the Fault screen will be
displayed. To silence the chime, select SILENCE. To display the fault
and resolve immediately, select DISPLAY. Use the up and down
arrows to scroll through the faults. Resolve the issue with the action
listed in Description of Fault Codes chart.
Full One Year Warranty
The D
E
WALT JobSite Security Portable Alarm System is warranted for
one year from date of purchase. We will repair, without charge, any
defects due to faulty materials or workmanship. For warranty repair
information, visit www.dewalt.com or call 1-800-4-D
defects due to faulty materials or workmanship. For warranty repair
information, visit www.dewalt.com or call 1-800-4-D
E
WALT
(1-800-433-9258). This warranty does not apply to accessories or
damage caused where repairs have been made or attempted by oth-
ers. This warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
damage caused where repairs have been made or attempted by oth-
ers. This warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
Fault Code
Fault Display
Description
Action
DevPower
Primary Power
No battery power
Change battery,
Lost Device #
in device
reset
DevLowBatt
Low Battery
Device battery
Change battery,
Device #
low
reset
DESCRIPTION OF FAULT CODES
Télécommande porte-clé DS200
AVERTISSEMENT : Lire et comprendre tout avertissement
et toute instruction inclus dans ce manuel. De plus lire, tout
et toute instruction inclus dans ce manuel. De plus lire, tout
avertissement et toute instruction fournis avec le Système d’alarme
mobile de sécurité des chantiers DS100.
mobile de sécurité des chantiers DS100.
MISE EN GARDE : RISQUES D’EXPLOSION, DE BLESSURE
OU D’INCENDIE. Suivre attentivement toute instruction ou tout aver-
tissement inclus sur l’étiquette ou l’emballage des piles.
•
tissement inclus sur l’étiquette ou l’emballage des piles.
•
Ne jamais utiliser une pile endommagée ou usée.
•
Les piles déchargées doivent être remplacées par des piles au lithi-
um de type CR-2 de 3,0 volts.
um de type CR-2 de 3,0 volts.
•
Ne pas utiliser de piles rechargeables ou tenter de recharger les
piles.
piles.
•
Retirer soigneusement la vieille pile déchargée.
•
Ne pas chercher à l’ouvrir.
•
Ne pas retirer l’étiquette d’une pile.
•
Ne jamais mettre une pile au feu.
•
S’en défaire conformément aux régulations locales.
•
Recycler les piles.
•
Lors de l’installation des piles, toujours respecter la polarité (+ et -)
inscrite sur les piles et l’appareil.
inscrite sur les piles et l’appareil.
•
Ne pas forcer excessivement pour installer des piles. Si la pile ne
rentre pas, vérifier que la polarité des bornes cadre avec les mar-
ques sur l’appareil.
rentre pas, vérifier que la polarité des bornes cadre avec les mar-
ques sur l’appareil.
•
Ne jamais mettre les bornes des piles en contact avec tout autre
objet métallique. Cela pourrait provoquer un court circuit.
objet métallique. Cela pourrait provoquer un court circuit.
•
Éviter de les exposer à des températures extrêmes.
•
Après utilisation, entreposer les piles dans un lieu frais, sombre
et sec.
et sec.
•
Conserver les piles hors de la portée des enfants.
MISE EN GARDE : RISQUES DE MAUVAIS FONCTIONNEMENT
OU DE DÉFAILLANCE. Ne pas utiliser à proximité d’eau. L’appareil
risquerait d’être endommagé. Protéger l’appareil de tout liquide.
OU DE DÉFAILLANCE. Ne pas utiliser à proximité d’eau. L’appareil
risquerait d’être endommagé. Protéger l’appareil de tout liquide.