Applied Concepts Inc ACMI006 User Manual
OPERATING THE STALKER PATROL
Stationary Mode Speed Measurement
Perform the tuning fork test on the radar before using for traffic
measurements. See page 20 for instructions on this procedure.
measurements. See page 20 for instructions on this procedure.
Select stationary mode by pressing the MOV/STA key on the remote
control, then select the desired antenna by pressing the ANT key. To
transmit, press the XMIT/HOLD key. The XMIT icon should
appear on the display unit (Fig 3) indicating that a radar signal is
being transmitted.
control, then select the desired antenna by pressing the ANT key. To
transmit, press the XMIT/HOLD key. The XMIT icon should
appear on the display unit (Fig 3) indicating that a radar signal is
being transmitted.
S
XMIT FRONT
REAR
SAME SLOW
FAST LOCK
TARGET
PATROL
Fi 3
g
If a target is in range, such as one traveling 54 mph, the speed will
appear in the target window of the display unit (Fig 4); and a Doppler
audio tone, which is proportional to the target speed, will be heard
from the speaker. The target speed is continually measured and
displayed, and the Doppler audio tone is heard as long as the target is
present.
appear in the target window of the display unit (Fig 4); and a Doppler
audio tone, which is proportional to the target speed, will be heard
from the speaker. The target speed is continually measured and
displayed, and the Doppler audio tone is heard as long as the target is
present.
S
XMIT FRONT
REAR
SAME SLOW
FAST LOCK
TARGET
PATROL
Fi 4
Hold mode can be selected by pressing the XMIT/HOLD key on the
perating in VSS mode (see section titled “VSS
of
g
remote control. In hold mode, The XMIT icon will be off
(Fig 5) and no signal will be transmitted, preventing detection by
radar detectors.
(Fig 5) and no signal will be transmitted, preventing detection by
radar detectors.
NOTE: While o
OPTION” on Page 21) the radar uses the presence (or absence)
VSS pulses to automatically switch between moving mode and
stationary mode.
OPTION” on Page 21) the radar uses the presence (or absence)
VSS pulses to automatically switch between moving mode and
stationary mode.
S
XMIT
FRONT
REAR
SAME SLOW
FAST LOCK
TARGET
PATROL
Fig 5
pposite Lane Moving Mode Speed
O
Measurement
Measurement
fork test on the radar before using for traffic
ote
Perform the tuning
measurements. See page 20 for instructions on this procedure.
measurements. See page 20 for instructions on this procedure.
Select moving mode by pressing the MOV/STA key on the rem
control. When S
control. When S
PATROL
is in moving mode, the patrol
window will contain either the patrol speed or a [ ]. The [ ] (Fig 6)
indicates that S
indicates that S
PATROL
is in moving mode, but has no
ground speed. Select opposite lane mode by pressing the
SAME/OPP key until the SAME icon is not visible. To transmit,
press the XMIT/HOLD key. The XMIT icon should appear on the
display unit (Fig 6) indicating that a radar signal is being transmitted.
Be sure the patrol speed indicated corresponds to the speedometer of
the patrol vehicle. If an approaching target is in the radar beam, its
speed will appear in the target window and a Doppler audio tone will
be heard from the speaker. Fig 7 is an example in which the patrol
speed is 50 and the approaching target speed is 68. The target speed
is continually measured and displayed and the Doppler audio tone is
heard while the S
SAME/OPP key until the SAME icon is not visible. To transmit,
press the XMIT/HOLD key. The XMIT icon should appear on the
display unit (Fig 6) indicating that a radar signal is being transmitted.
Be sure the patrol speed indicated corresponds to the speedometer of
the patrol vehicle. If an approaching target is in the radar beam, its
speed will appear in the target window and a Doppler audio tone will
be heard from the speaker. Fig 7 is an example in which the patrol
speed is 50 and the approaching target speed is 68. The target speed
is continually measured and displayed and the Doppler audio tone is
heard while the S
PATROL
is in transmit mode and a target is
present.
S
XMIT FRONT
REAR
SAME SLOW
FAST LOCK
TARGET
PATROL
Fig 6
S
XMIT FRONT
REAR
SAME SLOW
FAST LOCK
TARGET
PATROL
Fig 7
8