EMS Technologies Canada Ltd. HSD-128 User Manual
Page 2–28
18 September 2007
18 September 2007
SYSTEM DESCRIPTION, INSTALLATION, AND MAINTENANCE MANUAL
eNfusion™ HSD-128 High-speed Data Terminal
6.
Type in the parameter number for the Ocean Region LES access code you
want to change (i.e. 3, 21, 22, or 23), and then press Enter.
want to change (i.e. 3, 21, 22, or 23), and then press Enter.
The program prompts you to type in the LES access code.
7.
Type in the Ocean Region LES access code, and then press Enter.
Note:
You may change one or all of the LES defaults. Each must be entered
separately. Refer to Table 2–6 for access codes of the LES service
providers available at the time of publication. Contact Inmarsat directly
for the most up-to-date service provider and LES access code
information.
separately. Refer to Table 2–6 for access codes of the LES service
providers available at the time of publication. Contact Inmarsat directly
for the most up-to-date service provider and LES access code
information.
8.
In each parameter, enter a valid LES access code as needed.
CAUTION:
Do not change the Satellite Longitude parameter—press Enter
to continue.
9.
Reset the system. (In menu 2, press Z to reset the system, cycle the power
to the HSD transceiver, or press the front panel “Test” button or the remote
reset switch.)
to the HSD transceiver, or press the front panel “Test” button or the remote
reset switch.)
Note:
To activate the new default LES code(s) reset the system. If you
change the default LES code(s), but do not reset the system, the
system uses the “original” or previous default LES code(s)—even
though the “new” LES codes appear in the MENU 3 EEPROM
Listing—the new codes are activated (or loaded) when the system is
reset or the power is cycled.
change the default LES code(s), but do not reset the system, the
system uses the “original” or previous default LES code(s)—even
though the “new” LES codes appear in the MENU 3 EEPROM
Listing—the new codes are activated (or loaded) when the system is
reset or the power is cycled.
To confirm the activation of new LES access code after resetting the system:
1.
In Menu 3, press L.
2.
The EEPROM Listing appears. Confirm that the new LES access codes are
displayed correctly. (See bolded parameters below.)
displayed correctly. (See bolded parameters below.)
MISCELLANEOUS PARAMETERS
1 HPA-ANTENNA CABLE LOSS 18 AOR E VALID BEAMS
2 FORWARD ID 19 POR VALID BEAMS
3 AORW LES ACCESS CODE 20 IOR VALID BEAMS
4 TERRESTRIAL NETWORK ID 21 AORE LES ACCESS CODE
5 HPA-CHANNEL CARD CABLE LOSS 22 POR LES ACCESS CODE
6 MAX HPA GAIN 23 IOR LES ACCESS CODE
7 MIN ANTENNA GAIN 24 RECEIVER CALIBRATION (AERO)
8 MAX EIRP 25 MAX HPA POWER
9 MAX CHANNEL_CARD POWER 26 HPA RESERVED POWER (AERO)
10 NUMBER OF CHANNEL CARDS 27 CHANNEL CARD STARTUP DELAY
11 FRONT PANEL LEDS ENABLED 28 RX32 ACTIVE
12 RX ATTENUATION (LAND-ON-WINGS) 29 DEFAULT LATITUDE
13 MIN SECS BETWEEN CHAN CARD RESETS 30 DEFAULT LONGITUDE
14 MAINTENANCE PORT INVERSE VIDEO 31 OBEY OXCO STATUS
15 MAINTENANCE PORT DEGREES SYMBOL 32 CC DEBUG PORT
16 TERMINAL CATEGORY 33 COMBINED MODE BACKOFF ADJUSTMENT
17 AOR W VALID BEAMS
WHICH PARAMETER #
1 HPA-ANTENNA CABLE LOSS 18 AOR E VALID BEAMS
2 FORWARD ID 19 POR VALID BEAMS
3 AORW LES ACCESS CODE 20 IOR VALID BEAMS
4 TERRESTRIAL NETWORK ID 21 AORE LES ACCESS CODE
5 HPA-CHANNEL CARD CABLE LOSS 22 POR LES ACCESS CODE
6 MAX HPA GAIN 23 IOR LES ACCESS CODE
7 MIN ANTENNA GAIN 24 RECEIVER CALIBRATION (AERO)
8 MAX EIRP 25 MAX HPA POWER
9 MAX CHANNEL_CARD POWER 26 HPA RESERVED POWER (AERO)
10 NUMBER OF CHANNEL CARDS 27 CHANNEL CARD STARTUP DELAY
11 FRONT PANEL LEDS ENABLED 28 RX32 ACTIVE
12 RX ATTENUATION (LAND-ON-WINGS) 29 DEFAULT LATITUDE
13 MIN SECS BETWEEN CHAN CARD RESETS 30 DEFAULT LONGITUDE
14 MAINTENANCE PORT INVERSE VIDEO 31 OBEY OXCO STATUS
15 MAINTENANCE PORT DEGREES SYMBOL 32 CC DEBUG PORT
16 TERMINAL CATEGORY 33 COMBINED MODE BACKOFF ADJUSTMENT
17 AOR W VALID BEAMS
WHICH PARAMETER #
?