Digital Security Controls Ltd. 005132XS433 User Manual
4
This section describes how to enroll wireless devices (WLS904-433, WLS904P-
433, WLS906-433, WLS907-433, WLS912L-433 and WLS925L-433), and wireless
keys (WLS909-433/WLS919-433). For more information on these devices, read the
instruction sheet included with each device.
433, WLS906-433, WLS907-433, WLS912L-433 and WLS925L-433), and wireless
keys (WLS909-433/WLS919-433). For more information on these devices, read the
instruction sheet included with each device.
3.1 A Note about Electronic Serial Numbers
An electronic serial number (ESN) is printed on the back of each wireless device.
ESNs are used to enroll the wireless devices with the PC5132 receiver.
ESNs are used to enroll the wireless devices with the PC5132 receiver.
In order to reduce the occurrence of wireless devices with the same serial number,
6-digit serial numbers are now printed on the back of each wireless device. The 6-
digit serial numbers include hexadecimal digits. For instructions on programming
hexadecimal numbers, see your system
6-digit serial numbers are now printed on the back of each wireless device. The 6-
digit serial numbers include hexadecimal digits. For instructions on programming
hexadecimal numbers, see your system
Installation Manual, section 4: ‘How to
Program’.
NOTE: 6-digit serial numbers are only supported on the following control panels:
PC5020, PC501X, PC1565 and PC585 v2.0 and higher.
PC5020, PC501X, PC1565 and PC585 v2.0 and higher.
The WLS904(P)-433, WLS906-433, WLS907-433, WLS912L-433, and WLS925L-433
devices have both a 5-digit and a 6-digit serial number printed on them. When
connecting the PC5132 to a PC5010 v1.x panel, enter 5-digit serial numbers only. When
connecting the PC5132 to a PC5015 v2.x and higher, PC5020, PC5010, PC1565, or
PC585 panel enter the 6-digit serial number.
devices have both a 5-digit and a 6-digit serial number printed on them. When
connecting the PC5132 to a PC5010 v1.x panel, enter 5-digit serial numbers only. When
connecting the PC5132 to a PC5015 v2.x and higher, PC5020, PC5010, PC1565, or
PC585 panel enter the 6-digit serial number.
3.2 Enrolling Wireless Devices
1. At a system keypad, enter [
✱][8][Installer’s code] to go to the Installer
Programming section.
2. Enter programming section [804].
3. Enter the 2-digit number corresponding to the zone the device is to occupy
3. Enter the 2-digit number corresponding to the zone the device is to occupy
([01] to [32]).
NOTE: Hardwired and wireless devices cannot be assigned to the same zone.
PC5108 zone expander modules occupy zones in 2 groups of 4 (e.g. zones 9-12
and zones 13-16). None of the zones assigned to a PC5108 module may be used
for wireless devices. For more information on zone assignment, consult your sys-
tem Installation Manual.
PC5108 zone expander modules occupy zones in 2 groups of 4 (e.g. zones 9-12
and zones 13-16). None of the zones assigned to a PC5108 module may be used
for wireless devices. For more information on zone assignment, consult your sys-
tem Installation Manual.
4. Enter the device’s ESN. Follow the instructions in section 3.1 above.
5. Record the serial number and the assigned zone number in the
5. Record the serial number and the assigned zone number in the
programming worksheets in the back of this manual.
6. Continue with steps 3 - 5 until you have enrolled all wireless devices.
7. To exit press [#]. The device is now enrolled on the system.
7. To exit press [#]. The device is now enrolled on the system.
NOTE: The devices will not work properly until you complete zone and partition
programming (see section 4).
programming (see section 4).
S E C T I O N 3
Enrolling Wireless Devices