Digital Security Controls Ltd. 06PC5132 User Manual
10
Testing & Mounting
S E C T I O N 5
5.1 Test the Reception of Wireless Devices
It is very important to test the proposed placement of each wireless device before it is
mounted. Following these steps will test the signal strength between the RF5132-433
and the wireless devices.
You can test all of the devices together (global placement testing) or test each device
individually. To test all the devices together, see ‘Testing All Wireless Devices
Together’ below. To test wireless devices individually, see ‘Testing Individual
Devices’.
mounted. Following these steps will test the signal strength between the RF5132-433
and the wireless devices.
You can test all of the devices together (global placement testing) or test each device
individually. To test all the devices together, see ‘Testing All Wireless Devices
Together’ below. To test wireless devices individually, see ‘Testing Individual
Devices’.
After you have enrolled the wireless devices, you must exit and then
re-enter Installer’s Programming at least once before you can perform a
placement test.
placement test.
Testing All Wireless Devices Together:
1. Temporarily put the WLS904P-433, WLS906-433, WLS907-433, WLS912-433,
WLS914-433 and WLS925L-433 devices in the places you want to mount them.
2. At a system keypad, enter [*][8][Installer Code].
3. Enable the Global Module Placement test by entering section [804]. Then
enter sub-section [90] and turn on option [8].
4. Press [#] twice.
5. Enter programming section [904], then enter [01].
6. Activate one of the devices being tested until a result is displayed on the
keypad or sounded by the keypad or bell:
WLS904P-433/WLS914-433:
To perform a Placement Test on the WLS904P-
433, remove the detector from the back plate and then replace it. Once the
detector is replaced on the back plate the LED on the detector will flash
rapidly 5 times (4 times for the WLS914-433) to indicate that it has sent a
transmission. The panel will show and/or sound the result of the placement
test on the keypad. To perform a 2
detector is replaced on the back plate the LED on the detector will flash
rapidly 5 times (4 times for the WLS914-433) to indicate that it has sent a
transmission. The panel will show and/or sound the result of the placement
test on the keypad. To perform a 2
nd
and 3
rd
test, repeat this procedure.
Carefully replace the backplate onto the detector, ensuring that “TOP” is
Carefully replace the backplate onto the detector, ensuring that “TOP” is
Carefully replace the backplate onto the detector, ensuring that “TOP” is
Carefully replace the backplate onto the detector, ensuring that “TOP” is
Carefully replace the backplate onto the detector, ensuring that “TOP” is
facing upward, or you may damage the tamper switch.
facing upward, or you may damage the tamper switch.
facing upward, or you may damage the tamper switch.
facing upward, or you may damage the tamper switch.
facing upward, or you may damage the tamper switch.
facing upward, or you may damage the tamper switch.
NOTE:
When you remove the detector from the backplate (tamper the unit), the de-
tector will also be put into “Detector Walk Test” mode. While in Walk Test mode the
detector will activate the LED when motion is detected. The detector will also send a
signal to the receiver 5 seconds after motion is detected, indicated by 5 rapid flashes
by the LED. The LED will only work in this fashion for 10 motion detections after a
tamper/restore. Note that the panel will ignore these transmission signals with re-
spect to a placement test. The only way in which the panel will acknowledge a place-
ment test is if the backplate has, each time, been removed and restored.
detector will activate the LED when motion is detected. The detector will also send a
signal to the receiver 5 seconds after motion is detected, indicated by 5 rapid flashes
by the LED. The LED will only work in this fashion for 10 motion detections after a
tamper/restore. Note that the panel will ignore these transmission signals with re-
spect to a placement test. The only way in which the panel will acknowledge a place-
ment test is if the backplate has, each time, been removed and restored.
WLS906-433:
Remove the detector from its backplate, wait 5 seconds and re-
attach it, or hold a magnet near the raised line on the outer rim, then remove it.
WLS907-433/WLS925L-433:
Open the contact by moving the magnet away
from the unit. The keypad will show/sound the test result. After the first test
result has been generated (about 10 seconds) close the contact to generate
another test result. If the unit is attached to a door or a window, open and
close the door or window to activate the device.
result has been generated (about 10 seconds) close the contact to generate
another test result. If the unit is attached to a door or a window, open and
close the door or window to activate the device.