Digital Security Controls Ltd. 09GS260L User Manual
9
Introduction
The GS2060/GS2065 Communicator is a GSM / GPRS wireless alarm communicators that send alarm system information to a
System I, System II, or System III receiver through the GSM / GPRS digital cellular network.
The TL206GS/TL265GS Communicators are dual-path alarm communicators that send alarm system information to a System I,
System II, or System III receiver through the Ethernet / Internet or the GSM / GPRS digital cellular network.
System I, System II, or System III receiver through the GSM / GPRS digital cellular network.
The TL206GS/TL265GS Communicators are dual-path alarm communicators that send alarm system information to a System I,
System II, or System III receiver through the Ethernet / Internet or the GSM / GPRS digital cellular network.
The performance of the TL260GS/TL265GS/GS2060/GS2065 Communicator depends greatly on GSM network coverage. It
should not, therefore, be mounted without first performing placement tests to determine the best location for reception (minimum
of one green LED On). Optional antenna kits are available.
should not, therefore, be mounted without first performing placement tests to determine the best location for reception (minimum
of one green LED On). Optional antenna kits are available.
Installation of the Communicator requires activation with CONNECT 24 to operate. Dealer application forms and additional infor-
mation on the CONNECT 24 Voice Response Unit (VRU) and web user-interface can be found at www.connect24.com or at the
following telephone numbers:
mation on the CONNECT 24 Voice Response Unit (VRU) and web user-interface can be found at www.connect24.com or at the
following telephone numbers:
USA 1-888-251-7458 CANADA 1-888-955-5583
Installation of the Communicator requires the local installer to perform all module programming.
NOTE:
A computer with Internet access is necessary for this programming.
To program the Communicator, take the following steps:
1
. On your hard drive, locate the laptop’s IP address. Retrieve the number of the listening port; this is assigned by the applica-
tion. You should also have on hand the Communicator’s phone number.
2
. Using this phone number send the Communicator an 18-digit SMS text message. This SMS text message is to be config-
ured as: ! + IP address + Port number, without stops or spaces (e.g. !11122233344412345). Note that if you intend to use a
port number on your system of less than five digits, this number must be padded with zeroes to bring it up to five digits in
length (E.g. Port number 123 must become 00123; note that the zeroes must be added to the beginning of the port number).
This message contains the information which allows the Communicator to link up with your laptop.
port number on your system of less than five digits, this number must be padded with zeroes to bring it up to five digits in
length (E.g. Port number 123 must become 00123; note that the zeroes must be added to the beginning of the port number).
This message contains the information which allows the Communicator to link up with your laptop.
3
. With an existing installation of DLS IV downloading software on your laptop, you now have the ability to program the
Communicator using the GUI on the screen. See Options on page 23 for detailed programming information. Also, please refer
to your DLS IV manual.
to your DLS IV manual.
For UL Residential Fire and Burglary installations, the TL260GS/TL265GS/GS2060/GS2065 Communicator is listed as a pri-
mary (sole) communication means or as a backup when used in conjunction with a POTS line (dialer).
For UL Commercial Burglary installations, the TL260GS/TL265GS/GS2060/GS2065 Communicator is listed for supplemen-
tary (backup) use in conjunction with a POTS line (dialer).
mary (sole) communication means or as a backup when used in conjunction with a POTS line (dialer).
For UL Commercial Burglary installations, the TL260GS/TL265GS/GS2060/GS2065 Communicator is listed for supplemen-
tary (backup) use in conjunction with a POTS line (dialer).
This GSM / Ethernet Communicator is fixed and shall be installed by Service Persons only (Service Person is defined as a person
having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in
performing a task and of measures to minimize the risks to that person or other persons). It shall be installed and used within an
environment that provides the pollution degree max 2, over voltages category II, in non-hazardous, indoor locations only. This
manual shall be used with the Installation Manual of the alarm control panel. All instructions specified within that manual must be
observed.
having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in
performing a task and of measures to minimize the risks to that person or other persons). It shall be installed and used within an
environment that provides the pollution degree max 2, over voltages category II, in non-hazardous, indoor locations only. This
manual shall be used with the Installation Manual of the alarm control panel. All instructions specified within that manual must be
observed.
Models
• TL260GS (Ethernet + GSM/GPRS dual-path)
• GS2060 (GSM only)
• GS2060 (GSM only)
The above models are suitable for the PC1616 / PC1832 / PC1864 cabinets.
• TL265GS (Ethernet + GSM)
• GS2065 (GSM only)
• GS2065 (GSM only)
The above models are suitable for the PC9155 plastic enclosure.
Features
• Fully redundant Internet and GSM/GPRS dual-path alarm communication (TL265GS/TL260GS only)
• Back up and primary GSM/GPRS alarm communication (GS2065/GS2060 only)
• Integrated call routing (TL265GS/TL260GS only)
• Panel remote uploading/downloading support
• Back up and primary GSM/GPRS alarm communication (GS2065/GS2060 only)
• Integrated call routing (TL265GS/TL260GS only)
• Panel remote uploading/downloading support