Digital Security Controls Ltd. 09GS260L User Manuals

Table of Contents

• TL260GS / TL265GS

  1
• TL260GS / TL265GS

  1
• Installation Manual

  1
• Limited Warranty

  2
  • International Warranty

    2
  • Warranty Procedure

    2
  • Conditions to Void Warranty

    2
  • Items Not Covered by Warranty

    2
  • Disclaimer of Warranties

    3
  • Out of Warranty Repairs

    3
• WARNING

  4
  • Note to Installers

    4
  • System Failures

    4
  • Criminal Knowledge

    4
  • Access by Intruders

    4
  • Power Failure

    4
  • Failure of Replaceable Batteries

    4
  • Compromise of Radio Frequency (Wireless) Devices

    4
  • Smoke Detectors

    4
  • Motion Detectors

    5
  • Warning Devices

    5
  • Telephone Lines

    5
  • Insufficient Time

    5
  • Component Failure

    5
  • Inadequate Testing

    5
  • Security and Insurance

    5
  • Warning

    6
• FCC

  6
  • Industry Canada Statement

    6
  • IMPORTANT - READ CAREFULLY:

    7
• Introduction

  10
  • 1 . On your hard drive, locate the laptop’s IP address. Retrieve the number of the listening port; this is assigned by the application. You should also have on hand the Communicator’s phone number.

    10
  • 2 . Using this phone number send the Communicator an 18-digit SMS text message. This SMS text message is to be configured as: ! + IP address + Port number, without stops or spaces (e.g. !11122233344412345). Note that if you intend to use a port numbe...

    10
  • 3 . With an existing installation of DLS IV downloading software on your laptop, you now have the ability to program the Communicator using the GUI on the screen. See Options on page 23 for detailed programming information. Also, please refer to your...

    10
  • Models

    10
  • Features

    10
  • Technical Specifications

    11
  • Ratings

    12
    • Table 1: Communicator Ratings

      12
  • Compatibility

    13
    • Table 2: Compatible Receivers and Control Panels

      13
  • Table 2: Compatible Receivers and Control Panels

    13
• INSTALLING THE GSM / ETHERNET COMMUNICATOR

  14
  • 1 . Wire the telephone line, if available.

    14
  • 2 . Wire the PC9155 panel (but not the Communicator).

    14
  • 3 . Turn on the PC9155 panel. Program the panel’s telephone number, account code, format, GS / IP module enable, and the communication path priority (i.e. PSTN > Ethernet > GRPS).

    14
  • 4 . Turn off the panel.

    14
  • 5 . Wire the Communicator through the PC-Link.

    14
  • 6 . Proceed to CONNECT 24 Activation Information below.

    14
  • 7 . Turn on the panel. Wait for the initialization of the Communicator.

    14
  • 1 . Assemble the Communicator

    14
  • 2 . Install the Communicator module into the Cabinet

    15
  • 3 . Turn on the panel and check signal strength.

    15
  • 1 . Attach the Communicator to the inside of the PC9155 control panel cabinet if not already present.

    16
  • 2 . Turn on the PC9155 cabinet and check signal strength.

    17
  • 1 . Program the hexadecimal digits (DCAA) in the telephone number that will be used to contact the GSM / Ethernet Communicator (panel Options 301, 302, 303, ‘Telephone Phone Number Programming’).

    18
  • 2 . In Option 350, program the communication format as SIA FSK.

    18
  • 3 . In Options 351 through Option 376, program the call direction sub-options for the phone number being used to communicate using the GSM / Ethernet Communicator.

    18
  • 4 . Option 382, sub-option 5 must be set to ON.

    18
• STATUS LEDs

  19
  • Trouble Status LED

    19
    • Table 3: Trouble Status LED

      19
  • Network Connection Status LED

    21
  • Signal Strength LEDs

    21
    • Table 4: Radio Signal Strength

      21
      • 1 . Turn off the power to the Communicator by physically unplugging the unit from its power supply.

        21
      • 2 . Attach one end of the extension cable to the Communicator and the other end to the antenna itself.

        21
      • 3 . Reattach the power supply and turn on.

        21
      • 4 . Move the antenna around until you have received a strong signal.

        21
      • 5 . Mount the antenna bracket at that location.

        21
      • 1 . Locate the set of five vertically aligned pins in the middle of the Communicator board.

        21
      • 2 . Counting from the bottom, the first three pins are reserved for future use. You may discount these.

        21
      • 3 . The final two pins require a jumper in order to reset the hardware values.

        21
      • 4 . Turn off power to the Communicator.

        21
      • 5 . Apply the jumper to the two pins.

        22
      • 6 . Turn on power to the Communicator. Wait for ten seconds.

        22
      • 7 . Remove the jumper from the pins.

        22
    • Table 5: Communicator Troubles on a 9155 Panel

      22
• Options

  24
  • System Options

    24
    • Table 6: Window Times

      25
    • Table 7: System Toggle Options

      25
  • GPRS Options

    29
  • System Information

    29
• Programming Worksheets

  30