Digital Security Controls Ltd. 09LC171 User Manual
16
11 Specifications
•
Specifications are subject to change without prior notice.
FCC COMPLIANCE STATEMENT
FCC ID: F5309LC171
CAUTION: Changes or modifications not expressly approved by Digital
Security Controls could void your authority to use this equipment.
CAUTION: Changes or modifications not expressly approved by Digital
Security Controls could void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not
installed and used properly, in strict accordance with the manufacturer’s
instructions, may cause interference to radio and television reception. It
has been type tested and found to comply with the limits for Class B
device in accordance with the specifications in Subpart "B" of Part 15 of
FCC Rules, which are designed to provide reasonable protection
against such interference in any residential installation. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to television or radio
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
installed and used properly, in strict accordance with the manufacturer’s
instructions, may cause interference to radio and television reception. It
has been type tested and found to comply with the limits for Class B
device in accordance with the specifications in Subpart "B" of Part 15 of
FCC Rules, which are designed to provide reasonable protection
against such interference in any residential installation. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to television or radio
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
· Re-orient the receiving antenna
· Relocate the alarm control with respect to the receiver
· Move the alarm control away from the receiver
· Connect the alarm control into a different outlet so that alarm control
and receiver are on different circuits.
· Relocate the alarm control with respect to the receiver
· Move the alarm control away from the receiver
· Connect the alarm control into a different outlet so that alarm control
and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced
radio/television technician for additional suggestions. The user may find
the following booklet prepared by the FCC helpful: "How to Identify and
Resolve Radio/Television Interference Problems". This booklet is
available from the U.S. Government Printing Office, Washington, D.C.
20402, Stock # 004-000-00345-4.
radio/television technician for additional suggestions. The user may find
the following booklet prepared by the FCC helpful: "How to Identify and
Resolve Radio/Television Interference Problems". This booklet is
available from the U.S. Government Printing Office, Washington, D.C.
20402, Stock # 004-000-00345-4.
INDUSTRY CANADA COMPLIANCE STATEMENT
IC:160A-LC171
The term ‘IC:’ before the radio certification number only signifies that
Industry Canada technical specifications were met.
The term ‘IC:’ before the radio certification number only signifies that
Industry Canada technical specifications were met.
This Class B digital apparatus complies with Canadian ICES-003
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
RTTE Compliance Statement:
Detection Method
Dual PIR AND MW
Microwave Frequency
24.125 GHz
Power Input
9.6 to 16Vdc
Current Draw
Active: 24mA (±5%)
Standby: 21mA (±5%)
Standby: 21mA (±5%)
Temp Compensation
Yes, Dual slope temperature compensation
Alarm Period
2 sec (±0.5sec)
Alarm Outputs
Form C (NC, NO, Common)
28Vdc 0.1 A with 10 Ohm series protection resistor
28Vdc 0.1 A with 10 Ohm series protection resistor
Tamper Switch(s)
Two Switches
N.C 28Vdc 0.1 A with 10 Ohm Series protection resistors
Opens when cover is removed from unit’s base or if base is removed from
wall
N.C 28Vdc 0.1 A with 10 Ohm Series protection resistors
Opens when cover is removed from unit’s base or if base is removed from
wall
Warm up Period
120sec (± 5sec)
LED Indicator
LED is ON during ALARM (configurable)
RF Immunity
10 V/m plus 80% AM from 80 MHz to 2GHz
ElectroStatic Immunity
6kV contact, 8kV air
Transient Immunity
1kV
Operation Temp
-35ºC ~ +55ºC
Dimensions
200mm x 86mm x 80mm
Weight
500gr.
European directives
RTTE directive:1999/5/EC
EMC directive: 2004/108/EC
Low Voltage directive: 2006/95/EC
RoHS directive: 2002/95/EC
EMC directive: 2004/108/EC
Low Voltage directive: 2006/95/EC
RoHS directive: 2002/95/EC
European standards
requirements:
requirements:
EN300 440-2; EN301 489-1; EN50130-4 +A1 +A2; EN61000-6-3+A11
EN60950-1
EN50131-1 / EN50131-2-4 / EN50130-5
EN60950-1
EN50131-1 / EN50131-2-4 / EN50130-5
USA & Canada
47CFR part 15, subpart C, section 15.245; 47CFR part 15, subpart B
RSS210; ICES-003
RSS210; ICES-003
Protection Degree
IEC 60529: IP 65