Digital Security Controls Ltd. 17LE4000 User Manual

24

Section 8: LE4000 Wiring Diagrams

Figure 8-1 LE4000 Wiring Diagram

Supervision

Relay

Optional

u

se of PGM

output (See

Programming)

WARNING: 

Incorrect connections may result in PTC failure or improper operation. Inspect wiring and ensure connections are correct before

 turning

 on.

All 

circuits 

are 

classified 

for 

UL

 installations 

as 

Power 

Limited/Class 

II 

Power 

Limited. 

Do 

not 

route 

any 

wiring 

over 

circuit 

boards. 

Maintain 

at 

least 

1” 

(25.4mm) 

separation. 

A

 

minimum 1/4” (6.4mm) separation must be maintained at all points between Power Limited wiring and all other Non-Power Limited w

iring.  Route wires as indicated in the diagram.

T

elephone Line

Connection

RJ-45

For use in dry indoor ordinary locations only

. For installation refer to NFP

A70, 72.

Examples of control units/Subscribers Unit or power supplies compatible models: 

DSC PC1864, HS2128, PC5204, HSM2204. 

Electrical Ratings: 13.8 V

DC

 / 700 mA

  use 

ADP1310W

-NAU/NA

 (US/CDN) and 

Ba

ttery: 7.2V/2.2Ah 

Electrical ratings: 9-14V

DC

/500mA

 use listed control panel or power supply

Alarm Control Panel with

Dialler Interface

(Supports Contact ID 

format)

Sealed

Rechargeable

7.2V / 2.2Ah

RM1-UL

 Installations

RM1C-ULC Installations

Connect relay contacts to a zone input on the alarm control 

panel for LE4000 troubles supervision (24hr-type zone)

Panel 

Aux Power or External Power Supply 

AUX 

Output of the control panel (which can power the 

communicator) shall be rated LPS (power limited). Use only 

power supplies that have 

AUX output isolated from EGND 

T

ypical battery charge: 30-50 mA

Recommended Model: NiMH, Rated 7.2V

, 2.2Ah

Use only: Model 6PH-H-AA2200-S-D22 from Great Power

. 

TIP

RING

T1

R1

Z1

PGM1

Z2

PGM2

DC IN

+

-

1

2

3

4

5

6

7

9

8

10

WARNING!

Inputs to be connected

to dry contact outputs

from alarm control panel

(Use No. 26 

A

WG 

wires for the

connection to PSTN)

1K5

For UL

 Installations, the system shall be installed in accordance with chapter 2 of the 

ANSI/NFP

A

 72 and 

ANSI/NFP

A70. Recommended loca-

tions and wiring methods shall be in accordance with the National Electrical Code, 

ANSI/NFP

A

 70, the Standard for Installation and Classifica-

tion of Burglar and Holdup 

Alarm Systems, UL

 681, and the Standard for Central-Station 

Alarm Services, UL

 827.

For ULC Installations, the recommended locations and wiring methods shall be in accordance with CSA

 C22.1, Canadian Electrical Code, Part

I, Safety Standard for Electrical Installations; CAN/ULC-S302, Installation and Classification of Burglar 

Alarm Systems for Financial and Com-

mercial Premises, Safes and V

aults; and CAN/ULC-S301, Standard for Central and Monitoring Station Burglar 

Alarm Systems and  the Stan-

dard for the Installation of Residential Fire W

arning Systems, CAN/ULC-S540. Do not install the equipment in places where the signal strength

does not meet the minium recomended signal strength level. Do not run zone inputs and 

T1/R1 wiring along 

AC wires or other circuits with high

frequency signals in order to reduce possibility of interference and false alarms.

LE4000 Installation Manual