Digital Security Controls Ltd. 18LE2077 User Manual
19
NOTE: If no value is programmed and DHCP is used, the DHCP Server will configure the
address. If an address is programmed and DHCP is used, the address that you program will be
used instead of the DHCP address.
[008] DNS Server IP 2
[008] DNS Server IP 2
i
Programming this Section is not permitted on a UL/ULC listed system.
Default (000.000.000.000)
Enter the IP address for DNS Server 2. Format is 4 fields, each field is a 3 digit decimal. Valid
range: 000-255.
NOTE: If no value is programmed and DHCP is used, the DHCP Server will assign this value. If an
NOTE: If no value is programmed and DHCP is used, the DHCP Server will assign this value. If an
address is programmed and DHCP is used, the address that you program will be used instead of
the DHCP address.
P
ROGRAMMING
O
PTIONS
[010] System Toggle Option
Default (Disable)
[1] This bit is used to enable/disable two way audio over 3G.
Default (Disable)
[1] This bit is used to enable/disable two way audio over 3G.
[011] Installer Code
Default (CAFE)
Program your installer code for this Communicator module. The installer code will be required
when programming the Communicator module. Valid range: 0000 - FFFF.
when programming the Communicator module. Valid range: 0000 - FFFF.
[012] DLS Incoming Port
Default (0BF6/3062)
The DLS Incoming Local Port (listening port) is the port DLS IV will use when connecting to the
Communicator. If a router or gateway is used, it must be programmed with a Transmission Con-
trol Protocol (TCP) port forward for this port to the Communicator module IP address. Valid
range: 0000 - FFFF.
Default (0BF6/3062)
The DLS Incoming Local Port (listening port) is the port DLS IV will use when connecting to the
Communicator. If a router or gateway is used, it must be programmed with a Transmission Con-
trol Protocol (TCP) port forward for this port to the Communicator module IP address. Valid
range: 0000 - FFFF.
[013] DLS Outgoing Port
Default (0BFA/3066)
The DLS Outgoing Port is used for outgoing session to DLS IV after an SMS request has been
sent to the Communicator. Use this Section to set the value of the local outgoing port. The value
must be changed if the Communicator is located behind a firewall and must be assigned a par-
ticular port number, as determined by your network administrator. In most cases, changing the
default value or configuring your firewall with this port is not required.
Valid range: 0000-FFFF.
NOTE: If Section [006] Toggle Option [7] is ON, DLS will use the Primary path for session. If
Default (0BFA/3066)
The DLS Outgoing Port is used for outgoing session to DLS IV after an SMS request has been
sent to the Communicator. Use this Section to set the value of the local outgoing port. The value
must be changed if the Communicator is located behind a firewall and must be assigned a par-
ticular port number, as determined by your network administrator. In most cases, changing the
default value or configuring your firewall with this port is not required.
Valid range: 0000-FFFF.
NOTE: If Section [006] Toggle Option [7] is ON, DLS will use the Primary path for session. If
Section [006] Toggle Option [7] is OFF DLS will use the Ethernet path, if available.
[020] Time Zone
Default (00)
Use Column 2 (Offset Hours) to find your local Time Zone. Record the two digit HEX value from
Column 1 (HEX Value) on the same row. Program this HEX value for your Time Zone. Valid
range is 00 - FF.
Column 1 (HEX Value) on the same row. Program this HEX value for your Time Zone. Valid
range is 00 - FF.
Table 9: World Wide Time Zones
HEX
Value
Offset
Hours
Std
Abbrev
Location
01
-12
BIT
Baker Island Time
05
-11
NUT
Niue Time
SST
Somoa Standard Time