Digital Security Controls Ltd. 18LE2077 User Manual
31
NOTE: Minimum value is 000005 minutes. Programming an interval that is less than 5 minutes
will disable test transmission.
[226] Trouble Delay
Default (0F)
This option is used to program the delay, in minutes, for reporting an Ethernet Trouble, Cellular
Default (0F)
This option is used to program the delay, in minutes, for reporting an Ethernet Trouble, Cellular
Network, Insufficient Signal Strength, or Receiver Supervision Trouble to the panel. The timer is
only activated when Option 8 in [851][006], Trouble Suppression is enabled.
Valid entries are 00-FF.
00 = No Delay
FF = Cellular Network Trouble, Ethernet Trouble, Low Signal Strength and Receiver Supervision
Valid entries are 00-FF.
00 = No Delay
FF = Cellular Network Trouble, Ethernet Trouble, Low Signal Strength and Receiver Supervision
Trouble conditions are disabled.
01 - FE = Trouble Delay time in minutes.
01 - FE = Trouble Delay time in minutes.
[227] Voice Call Timeout
Default (00);
This option sets the Voice Call Timeout, in minutes. Programming a value of 00 will disable
timeout. Valid range is 00 to FF.
[228] Voice Call Back Time
[228] Voice Call Back Time
Default (0A);
This option sets the Voice call back time, in minutes. When the Communicator requests Call
Back from the receiver, it will answer incoming calls during the programmed timeout period. If
an incoming call is received after the timeout from requesting call back, the Communicator will
answer the call and immediately hang up. Programming a value of 00 will disable timeout
(accept all incoming calls). Default value is 0A/10 seconds. Valid range is 00 to FF.
Back from the receiver, it will answer incoming calls during the programmed timeout period. If
an incoming call is received after the timeout from requesting call back, the Communicator will
answer the call and immediately hang up. Programming a value of 00 will disable timeout
(accept all incoming calls). Default value is 0A/10 seconds. Valid range is 00 to FF.
[229] Voice Call Back Number
Default (SIM Telephone Number);
This option sets the Voice Call Back Telephone Number for the receiver. This number is used for
Two Way calling. Current SIM telephone number can be viewed in Section [996]. Valid entry is
32 character ASCII.
Two Way calling. Current SIM telephone number can be viewed in Section [996]. Valid entry is
32 character ASCII.
C
OMMAND
AND
C
ONTROL
O
PTIONS
[301] Command and Control Toggle Options
[1] SMS Notification Default (ON)
[1] SMS Notification Default (ON)
.
[2] Reserved Default ( )
.
[3] SMS Command and Control Default (ON).
[4] Reserved Default ( )
[4] Reserved Default ( )
.
[5] SMS Character Format Default.
ON: SMS Unicode, maximum message length is 70 characters.
OFF: 7 bit SMS, maximum message length is 160 characters.
[6] Long SMS Message Handling Default (OFF).
ON: If longer than maximum message length, it is split and sent as multiple SMS messages.
OFF: If longer than maximum message length, a single, truncated SMS message is sent.
[7-8] Reserved Default ( ).
ON: SMS Unicode, maximum message length is 70 characters.
OFF: 7 bit SMS, maximum message length is 160 characters.
[6] Long SMS Message Handling Default (OFF).
ON: If longer than maximum message length, it is split and sent as multiple SMS messages.
OFF: If longer than maximum message length, a single, truncated SMS message is sent.
[7-8] Reserved Default ( ).
[308] SMS Retry Attempts
(Default 19)
This section determines the number of times an SMS will be resent if the message is not deliv-
ered. Valid Entries are 00 to FF. 00 = Disabled, no SMS retry. 01 - FE = 01 to 254 attempts. FF
= Use default value of 19 (25 attempts).
(Default 19)
This section determines the number of times an SMS will be resent if the message is not deliv-
ered. Valid Entries are 00 to FF. 00 = Disabled, no SMS retry. 01 - FE = 01 to 254 attempts. FF
= Use default value of 19 (25 attempts).