OMG plc IMUAP1 User Manual
Safety and Regulatory Information
Page : 1
IMeasureU Sensor V1 Safety and Regulatory Information
The terms “device” or “wireless device” used in this section refers to your IMeasureU
Sensor V1 wearable product. Read this information before using your device.
Sensor V1 wearable product. Read this information before using your device.
Federal Communications Commission (FCC) Part 15 Information to User
Pursuant to part 15.21 of the FCC Rules, you are cautioned that changes or modifications
not expressly approved by Vicon Motion Systems Ltd could void your authority to operate
the device. This device complies with part 15 of the FCC Rules. Operation is subject to the
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15(c) of the FCC CFR47 rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency (RF) energy and, if not
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular application. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
not expressly approved by Vicon Motion Systems Ltd could void your authority to operate
the device. This device complies with part 15 of the FCC Rules. Operation is subject to the
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15(c) of the FCC CFR47 rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency (RF) energy and, if not
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular application. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.
FCC Notice and Cautions
The device may cause TV or radio interference if used in close proximity to receiving
equipment. The FCC can require you to stop using the equipment if such interference
cannot be eliminated.
equipment. The FCC can require you to stop using the equipment if such interference
cannot be eliminated.
Cautions: Any changes or modifications to your device not expressly approved by Vicon
Motions Systems Ltd could void your warranty for this equipment and void your authority
to operate this equipment. Only use approved batteries. The use of any unauthorized
accessories may be dangerous and void the device warranty if said accessories cause
damage or a defect to the device. Although your device is quite sturdy, it is a complex
Motions Systems Ltd could void your warranty for this equipment and void your authority
to operate this equipment. Only use approved batteries. The use of any unauthorized
accessories may be dangerous and void the device warranty if said accessories cause
damage or a defect to the device. Although your device is quite sturdy, it is a complex
piece of equipment and can be broken. Avoid dropping, hitting, bending or sitting on it.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
The published FCC ID is DMR-IMUAP1.