UTC Fire & Security Americas Corporation Inc 983-UDWS User Manual
P/N 466-4430
• REV A.09 • 24Jul13
1 / 2
Micro Door/Window Sensor Installation Sheet
Description
The Micro Door/Window Sensor is a
supervised, wireless sensor that detects the
opening and closing of doors, windows, or
drawers. The sensor and magnet are mounted
using double-sided adhesive tape or screws
(included).
supervised, wireless sensor that detects the
opening and closing of doors, windows, or
drawers. The sensor and magnet are mounted
using double-sided adhesive tape or screws
(included).
When activated, the sensor transmits an open
(trip) or close (restore) signal to the panel.
These are the signals the unit provides:
supervisory, tamper and low battery (as
needed).
(trip) or close (restore) signal to the panel.
These are the signals the unit provides:
supervisory, tamper and low battery (as
needed).
The sensor is powered by a replaceable 3-
VDC, lithium coin-cell battery.
VDC, lithium coin-cell battery.
Installation guidelines
•
Mounting the sensor on metal can reduce
its transmitting range. Therefore, test the
sensor from the desired location using the
dealer sensor test, before permanently
mounting it.
its transmitting range. Therefore, test the
sensor from the desired location using the
dealer sensor test, before permanently
mounting it.
•
Mount the sensor within 100 ft. of the
panel.
panel.
•
Mount the sensor on the frame, and the
magnet on the door, window, or drawer. If
mounting on double doors, mount the
sensor on the least used door and the
magnet on the other door.
magnet on the door, window, or drawer. If
mounting on double doors, mount the
sensor on the least used door and the
magnet on the other door.
•
Mount sensors at least 5 inches above the
floor to avoid damaging them.
floor to avoid damaging them.
Programming
The following steps describe the general
guidelines for programming (learning) the
sensor into panel memory. Refer to the
specific panel’s documentation for complete
programming details.
1.
guidelines for programming (learning) the
sensor into panel memory. Refer to the
specific panel’s documentation for complete
programming details.
1.
Set the panel to the program mode.
2.
Proceed to the LEARN SENSORS menu.
3. Select the appropriate sensor group and
sensor number assignments.
4.
When prompted by the
panel to trip the sensor
for learning, remove the
battery pull tab or remove
the sensor cover. The
system should
acknowledge learning
the sensor by touchpad
display and/or audio
(depending on the panel).
panel to trip the sensor
for learning, remove the
battery pull tab or remove
the sensor cover. The
system should
acknowledge learning
the sensor by touchpad
display and/or audio
(depending on the panel).
5.
Exit program mode.
Testing the sensor
1.
Set the panel to the sensor test mode.
2.
Take the sensor and magnet to the
desired mounting location, making sure to
line up their alignment marks with each
other.
desired mounting location, making sure to
line up their alignment marks with each
other.
3.
Trip the sensor by pulling the magnet
away from the sensor.
away from the sensor.
4.
Listen for the system siren beeps to
determine the appropriate response and
refer to the specific panel documentation.
determine the appropriate response and
refer to the specific panel documentation.
Mounting the sensor
Mount the sensor after successful programming
and testing are completed, using the supplied
mounting screws for all UL installations. For non-
UL installations, using the supplied double-sided
tape is optional.
and testing are completed, using the supplied
mounting screws for all UL installations. For non-
UL installations, using the supplied double-sided
tape is optional.
Note: The gap between the
sensor and magnet should be a maximum of
3/8”.
3/8”.
Mounting screws (UL Installations)
1.
Remove the sensor base from the sensor.
2.
Place the sensor base in desired location
and mount the base with the supplied
screws. Attach the sensor to the base.
and mount the base with the supplied
screws. Attach the sensor to the base.