UTC Fire & Security Americas Corporation Inc 983-UDWS User Manual
2 / 2
Micro Door/Window Sensor Installation Instructions
3.
Mount the magnet into the desired
location using the supplied screw and lock
washer, making sure the alignment mark
lines up with the sensor’s.
location using the supplied screw and lock
washer, making sure the alignment mark
lines up with the sensor’s.
Double-sided tape (optional for non-UL
installations)
1.
Before applying double-sided tape,
ensure that the desired location is a
smooth, clean and dry surface.
ensure that the desired location is a
smooth, clean and dry surface.
Note: When applying the double-sided
tape, evenly apply pressure to ensure a
good surface contact.
tape, evenly apply pressure to ensure a
good surface contact.
2.
Apply double-sided tape to the bottom of
the sensor and the magnet. Mount the
sensor and magnet at the desired
locations, ensuring the alignment marks
line up with each other.
the sensor and the magnet. Mount the
sensor and magnet at the desired
locations, ensuring the alignment marks
line up with each other.
3.
Retest the sensor using the procedure in
the section “Testing the Sensor”.
the section “Testing the Sensor”.
For additional tamper security
1.
Punch out the seal covering the screw
hole on the sensor cover.
hole on the sensor cover.
2.
With the sensor base secured to the
sensor, insert the smallest screw
supplied, securing the sensor base to the
sensor.
sensor, insert the smallest screw
supplied, securing the sensor base to the
sensor.
Replacing the battery
1.
Remove the sensor from the base then
remove the inner cover, exposing the
battery.
remove the inner cover, exposing the
battery.
2.
Remove the bad battery and install the
new battery. NOTE: Observe polarity of
the battery.
new battery. NOTE: Observe polarity of
the battery.
3.
Re-install the PC board, inner cover and
the sensor.
the sensor.
Specifications
Model no.
TX-1012-01-1 (white)
TX-1012-01-3 (brown)
TX-1012-01-3 (brown)
RF frequency
319.5 MHz
Compatibility
Interlogix Learn Mode Panels
and Receivers
and Receivers
Battery type
3-VDC, lithium coin-cell battery
UL Approved Battery
Duracell DL2032
Varta CR2032
Panasonic CR2032
Operating
temperature range
temperature range
32 to 120°F (0 to 49°C)
Storage temperature
range
range
-30 to 140°F (-34 to 60°C)
Relative humidity
0-85% non-condensing
Dimensions
(L x W x D)
(L x W x D)
1.9 x 1.0 x 0.50 in. (4.7 x 2.5 x
1.3 cm)
1.3 cm)
Regulatory information
Manufacturer
UTC Fire & Security Americas
Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN
55112-6943, USA
Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN
55112-6943, USA
FCC
compliance
compliance
This device complies with part 15 of
the FCC Rules. Operation is subject to
the following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
FCC ID: B4Z-983-UDWS
IC: 1175C-983UDWS
the FCC Rules. Operation is subject to
the following two conditions: (1) This
device may not cause harmful
interference, and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
FCC ID: B4Z-983-UDWS
IC: 1175C-983UDWS
This Class B digital apparatus
complies with Canadian ICES-003.
complies with Canadian ICES-003.
Cet appareil numérique de la classe B
est conforme à la norme NMB-003 du
Canada.
est conforme à la norme NMB-003 du
Canada.
UL
ANSI/UL 634 Connectors and
Switches for Use with Burglar-Alarm
Systems
Switches for Use with Burglar-Alarm
Systems
UL 1023
– Household Burglar-Alarm
System Units.
ULC
C634-M1986 - Connectors and
Switches for Use with Burglar-Alarm
Systems
Switches for Use with Burglar-Alarm
Systems
Contact information
For contact information, see
Trademark/Copyright
© 2013 UTC Fire & Security Americas
Corporation, Inc. Interlogix is part of UTC
Climate Controls & Security, a unit of United
Technologies Corporation. All rights reserved.