Velohub AG BLK User Manual
USER MANUAL
Please take a moment to read this manual before using
Blinkers. If you need further support, please contact us at
support@blinkers.io.
Blinkers. If you need further support, please contact us at
support@blinkers.io.
DE Für die Bedienungsanleitung auf Deutsch, besuchen Sie:
FR Pour le mode d’emploi en français, veuillez consulter:
ES Para la guía del usuario en español, por favor consulte:
IT Per il manuale di istruzioni in italiano, fare riferimento a:
IT Per il manuale di istruzioni in italiano, fare riferimento a:
1- WARNINGS
Blinkers are designed to be a complement of hand signals, and NOT
a replacement. You need to continue using your hands to indicate a
change of direction when you cycle in the road. Even if Blinkers
provide additional visibility and predictability, we can’t ensure that
vehicles around you will see and understand your intentions.
a replacement. You need to continue using your hands to indicate a
change of direction when you cycle in the road. Even if Blinkers
provide additional visibility and predictability, we can’t ensure that
vehicles around you will see and understand your intentions.
The remote control on the handlebar shows the turn signal that is
activated. Make sure you look at it every time you use it to check
that is indicating to the right direction. Indicating to the wrong direc-
tion can be very dangerous and increase the risk of accident.
activated. Make sure you look at it every time you use it to check
that is indicating to the right direction. Indicating to the wrong direc-
tion can be very dangerous and increase the risk of accident.
When plugging Blinkers into the mounts, do NOT put your finger on
the edge that plugs into the bike mounts, so that you don’t pinch
your fingers. Instead, hold Blinkers from one of the sides.
the edge that plugs into the bike mounts, so that you don’t pinch
your fingers. Instead, hold Blinkers from one of the sides.
The turning indicators, as well as the brake light and the regular
white and red lights are less visible during daylight.
white and red lights are less visible during daylight.
Do not attempt to access the components inside. It may damage
the electronics and will void your warranty.
the electronics and will void your warranty.
In case you have a Blinkers with laser, never look directly into the
laser beam, shine it at someone else’s eyes or at other vehicles.
Do not use optical instruments like microscope
laser beam, shine it at someone else’s eyes or at other vehicles.
Do not use optical instruments like microscope
,
telescope or
binoculars to view the laser beam. Do not point the laser at reflec-
tive surfaces
tive surfaces
.
Handle the laser functionality with care. It must never be used for
any other purpose other tan on your bicycle. Blinkers has a safety
feature that the laser cannot be used if it is not plugged in the rear
mount.
any other purpose other tan on your bicycle. Blinkers has a safety
feature that the laser cannot be used if it is not plugged in the rear
mount.
The laser is only visible during night conditions.
The laser has been programmed to work for only 10min at a time.
This is due to the heating that the laser generates when functio-
ning, which might damage its performance in the long-term if it is
used for too long.
This is due to the heating that the laser generates when functio-
ning, which might damage its performance in the long-term if it is
used for too long.
Blinkers contains a class 2M laser according to IEC 60825. It has an
output power of <5mW, and wavelength of 510-525nm.
output power of <5mW, and wavelength of 510-525nm.
2- CHARGING
Before using Blinkers, you need to fully charge the battery.
To charge your light(s):
1.
To charge your light(s):
1.
Open the USB cover on the back of the light
2.
Connect the USB cable and power Blinkers with 5 VDC voltage.
3.
Once charging, the screen will indicate the level of battery for 2 s
4.
Once fully charged (~2,5 h), close the USB cover
.
Do not pull too hard he USB cover. You may take it out from its
hole.
hole.
4- MOUNTING
Front Mount
1.
Select the appropriate clamp.
2.
Select the appropriate rubber insert and fit it into the clamp. The
appropriate dimensions are printed on the rubber bands.
appropriate dimensions are printed on the rubber bands.
3.
Slide the clamp over the handlebar with the bolt hole facing for-
ward, place the front mount on the clamp, and insert the long
screw.
ward, place the front mount on the clamp, and insert the long
screw.
Handlebar diameter
Type of clamp
Ø23-26 mm
Small clamp
Ø28-33 mm
Big clamp
Saddle Mount
1.
Make sure your saddle is compatible with the rear mount.
Compatible
saddles &
dimensions
saddles &
dimensions
-1-
-2-
-3-
-6-
-7-
-4-
2.
Fit the rubber insert onto the main holder and place it below the
tubes under the saddle.
tubes under the saddle.
3.
Place the top holder on top of the tubes below the saddle. Insert
the three screws from the bottom.
the three screws from the bottom.
4.
Tighten the 3 short screws until the mount fits the tubes.
Note: if you have a rack or a basket, check the rack mount in our website
-8-
-9-
4.
Tighten the screw until the clamp fits the handlebar. Do not fully
tighten it for now.
tighten it for now.
5.
Place the Front Blinker into the front mount (magnetic attachment),
and regulate the angle of the white light.
and regulate the angle of the white light.
6.
Once the Blinker is at the correct angle, tighten the bolt using the
allen key until the clamps fits well and cannot rotate anymore.
allen key until the clamps fits well and cannot rotate anymore.
3- PAIRING
Before using Blinkers for the first time, you need to pair the light(s) with
the remote control. To pair your light(s):
1.
1.
Make sure your Blinkers are charged. See 2– CHARGING.
2.
Connect Blinkers to USB cables or plug them in the mounts.
3.
Press the top and low buttons of the control pad for 3s and wait
until the “L” and “R” lights turn on. See “Remote control sketch”.
until the “L” and “R” lights turn on. See “Remote control sketch”.
4.
Bring the remote control close to the rear Blinker (max.10cm) and
wait until the low green light on the remote control turns on.
wait until the low green light on the remote control turns on.
5.
Now, if you have a front Blinker, bring the remote control close to
the front Blinker (max.10cm) and wait until the top red light of the
remote control turns on.
the front Blinker (max.10cm) and wait until the top red light of the
remote control turns on.
6.
Finally, all the lights of the remote control will start blinking: it
means that the Blinkers and the remote control are paired.
means that the Blinkers and the remote control are paired.
Make sure you pair the rear Blinker first, before the front.
If you have a Blinker Set, but you end up using only one Blinker,
we recommend that you re-pair the single Blinker alone with the
remote control. You can also pair the front Blinker alone.
we recommend that you re-pair the single Blinker alone with the
remote control. You can also pair the front Blinker alone.
Rubber band
Long screw M4
+ washer
+ washer
Clamp
Front mount
Front Blinker
Top holder
Main holder
Rear Blinker
3x Short screws M4
+ washers
+ washers
-5-
-10-
R button
L button
Top button
Low button
Bottom rubber cover
Remote control sketch
Rubber band