Panasonic Corporation of North America 9TAWX-CT2020 User Manual
● Channel Group Selection
You can select a channel group by setting the channel
selector, which is the rotary switch inside the switch pocket.
selector, which is the rotary switch inside the switch pocket.
1. Press the power button to turn off the order taker unit.
2. Set the switch to the channel group.
Available Channel Group: 1 - 8
Notes:
• When a switch position other than 1 through 8 is select-
ed, the power indicator will blink in red.
• Be sure to turn off the order taker unit in Step 1.
Otherwise, the channel group will not be activated until
you turn off and on the power again.
you turn off and on the power again.
● DIP Switch Setup
An eight-bit DIP switch is provided for system setups. The
initial settings are marked with an asterisk *.
initial settings are marked with an asterisk *.
1. Press the power button to turn off the order taker unit.
2. Set the switches as follows.
SW#1: For selection of a radio frequency suitable for
the location
ON: Applies the US frequency to the headset.
OFF: Applies the Canadian frequency.
OFF: Applies the Canadian frequency.
7
1
2
3
4
5
6
7
8
G
1 2 3 4 5 6 7 8
Channel selector
1
SW#
2
3
4
5
6
7
8
Location
Function
DDT/SDT
Manager Mode
Role Assignment
Area Expansion
Tone Squelch
Talk Lock Resumption
Compatibility
USA*
ON
Double Drive Thru
ON
Manager
Expand
ON*
ON
WX-C1010/WX-C1011
Canada
OFF
Single Drive Thru*
OFF(Normal)*
Assistant*
Normal*
OFF
OFF*
WX-CC2010*
SW#2: Refer to the Operating Instructions included with
the WX-CC2010.
SW#3: Refer to WX-CC2010 Operating Instructions.
SW#4: Refer to WX-CC2010 Operating Instructions.
SW#5: Refer to WX-CC2010 Operating Instructions.
SW#6: Enables or disables the tone squelch function.
ON: Outputs audio after detecting the tone squelch.
OFF: Outputs audio disregarding the tone squelch.
OFF: Outputs audio disregarding the tone squelch.
Note: Normally, set SW#6 to ON. Pay attention to a
high level noise that may be output when set to
OFF.
OFF.
SW#7: While talking with a customer in the Talk Lock
mode, you may need to contact store personnel in
the Page PTT or Page Lock mode, which interrupts
the Talk Lock mode. This switch specifies the status
of the interrupted Talk Lock mode after ending the
Page PTT or Page Lock mode.
the Page PTT or Page Lock mode, which interrupts
the Talk Lock mode. This switch specifies the status
of the interrupted Talk Lock mode after ending the
Page PTT or Page Lock mode.
ON: Resumes the Talk Lock mode.
OFF: Releases the Talk Lock mode.
OFF: Releases the Talk Lock mode.
SW#8: Specifies the system compatibility.
ON: Is compatible with the center modules WX-
C1010 and WX-C1011.
OFF: Refer to WX-CC2010 Operating Instructions.
Notes:
• Be sure to turn off the order taker unit in Step 1.
Otherwise, the channel group (refer to "Channel
Group Selection") will not be activated until you turn
off and on the power again.
Group Selection") will not be activated until you turn
off and on the power again.
• SW#6 and SW#8 are used for channel interference
check while turn on the headset.
● Channel Interference Check
SW#6 and SW#8 have the specific function of checking
whether or not there is radio wave interference in the select-
ed channel group.
whether or not there is radio wave interference in the select-
ed channel group.
1. Press the power button to turn off the order taker unit.
<When WX-C1010 or WX-C1011 is used for the cen-
ter module>
ter module>
2. Set the switches as follows, and turn on the headset.
A noise will be heard in the headset.
SW#6: OFF
SW#8: ON
SW#8: ON